manualshive.com logo in svg

Stihl 561 C-M, Instruction Manual, Page: 20 / 28

Share
Download
Stihl 561 C-M Instruction Manual Download Page 20

recommends the following maintenance inter‐

vals:
After every 25 hours of operation

► Lubricate the gearbox.
After every 100 hours of operation

► Install a new spark plug.
Monthly

► Have fuel tank cleaned by a STIHL servicing

dealer.

► Have pickup body (filter) in fuel tank cleaned

by a STIHL servicing dealer.

Every 12 months

► Have pickup body (filter) in fuel tank replaced

by a STIHL servicing dealer.

16.2

Lubricating the Gearbox

2

1

0000-GXX-3044-A0

► Remove the screw plug (2).

► If no grease can be seen on the end of the

screw plug (2):

► Screw the tube (1) of STIHL gear grease

into the filler hole.

► Squeeze 5 g of STIHL gear grease into the

gear housing.

► Unscrew the tube (1) of STIHL gear grease.

► Refit and tighten down the screw plug (2)

firmly.

► Run the trimmer for 1 minute.

STIHL gear grease is distributed evenly.

16.3

Adjusting the throttle cable

► Shut off the engine.

2

3

1

0000097406_001

► Totally press throttle trigger lockout (1) and

throttle trigger (2) and keep pressed.

► Turn screw (3) clockwise until resistance is

felt.

► Continue turning screw (3) clockwise by half a

turn.

16.4

Sharpening and Balancing a

Metal Cutting Attachment

Correctly sharpening and balancing metal cutting

attachments requires a lot of practice.
STIHL recommends you have metal cutting

attachments resharpened and balanced by a

STIHL servicing dealer.

► Sharpen the metal cutting attachment as

described in the instructions and on the pack‐

aging supplied with the cutting attachment you

are using.

17 Repairing

17.1

Repairing the Trimmer and

Cutting Attachment

The trimmer and cutting attachment cannot be

repaired by the user.

► If the trimmer or cutting attachment is dam‐

aged: Do not use your trimmer or cutting

attachment and contact your STIHL servicing

dealer.

18 Troubleshooting

18.1

Troubleshooting Trimmer

Most problems can be attributed to the same cause.

► Carry out the following measures:

► replace the air filter.

► Clean or replace the spark plug.

► Adjust saw for winter or summer operation.

► If the problem continues: Carry out the measured listed below.

English

17 Repairing

20

0458-856-0121-A. VA0.B21.

Summary of Contents for 561 C-M





























Reviews:

No comments