background image

0000-GXX-4729-A0 

► Press the trimmer against the ground with

your left hand.

► Pull the starter grip slowly with your right hand

until you feel it engage.

► Pull the starter grip quickly and allow the

starter rope to rewind several times until the

engine runs.

► If the choke lever (2) is in the position  :

briefly press the throttle lever lockout (3) and

the throttle trigger (4).
The choke lever (2) springs to position  . The

engine runs at idling speed.

► If the cutting attachment rotates when the

engine is idling: Rectify the malfunction.

Throttle cable adjustment is not correct.

► If the engine does not start: Move the choke

lever (2) to position   and try again to start

the engine.

9.2

Shut off the engine

2

3

1

0000097402_001

► Release the throttle trigger (1) and throttle trig‐

ger lockout (2).

The cutting attachment comes to a standstill.

► Depress the stop switch (3).

The engine stops.

10 Testing the Trimmer

10.1

Checking the controls

Throttle trigger lockout and throttle trigger

► Shut off the engine.

► Attempt to pull the trigger without depressing

the lockout lever.

► If the trigger can be pulled: Do not use your

trimmer and contact your STIHL dealer for

assistance.

The throttle trigger lockout is defective.

► Press the throttle trigger lockout and keep

pressed.

► Depress the throttle trigger.

► Release the throttle trigger and throttle trigger

lockout.

► If the trigger or trigger lockout is stiff or does

not spring back to the idle position: Do not use

your trimmer and contact your STIHL dealer

for assistance.

Trigger or trigger lockout is faulty.

Throttle cable adjustment

► Start the engine.

► Attempt to pull the trigger without depressing

the lockout lever.

► If the engine accelerates: Adjust the throttle

cable.

Throttle cable adjustment is not correct.

Shut off the engine

► Start the engine.

► Depress the stop switch.

The engine stops.

► If the engine does not stop:

► Move the choke lever to position  .

The engine stops.

► Do not use your trimmer and contact a

STIHL servicing dealer for assistance.

The brushcutter is defective.

11 Operating the Trimmer

11.1

Winter Operation

The carburetor may ice up if the engine is oper‐

ated at temperatures below +10°C. The shutter

must be set to the winter mode so that carburetor

is additionally heated by warm air from around

the engine.

NOTICE

■ The engine may overheat if is operated in the

winter mode at temperatures above +10°C.

► Change setting to summer mode.

► Shut off the engine.

English

10 Testing the Trimmer

16

0458-856-0121-A. VA0.B21.

Summary of Contents for 561 C-M





























Reviews: