STIEBEL ELTRON WPE-I 04 HKW 230 Premium Administrator'S Manual For Operation And Installation Download Page 44

Page: 44 / 48

| WPE-I H(K)W 230 Premium

www.stiebel-eltron.com

GUARANTEE | ENVIRONMENT AND RECYCLING

Guarantee

The guarantee conditions of our German companies do not

apply to appliances acquired outside of Germany. In countries

where our subsidiaries sell our products a guarantee can only

be issued by those subsidiaries. Such guarantee is only grant-

ed if the subsidiary has issued its own terms of guarantee. No

other guarantee will be granted.
We shall not provide any guarantee for appliances acquired in

countries where we have no subsidiary to sell our products.

This will not affect warranties issued by any importers.

Environment and recycling

We would ask you to help protect the environment. After use,

dispose of the various materials in accordance with national

regulations.

GUaraNTEE

ENVirONmENT aND rECYCliNG

Summary of Contents for WPE-I 04 HKW 230 Premium

















































Search results

Summary of Contents for WPE-I 04 HKW 230 Premium

Reviews:

Related manuals for WPE-I 04 HKW 230 Premium

Brands by name

Popular brands

STIEBEL ELTRON WPE-I 04 HKW 230 Premium, Administrator'S Manual For Operation And Installation

Search results

Summary of Contents for WPE-I 04 HKW 230 Premium

Reviews:

Related manuals for WPE-I 04 HKW 230 Premium

Brands by name

Popular brands