OPERATION
Appliance description
12
| IA 2054 extreme
www.stiebel-eltron.com
WARNING Electrocution
-
Never insert any object into any aperture in the
appliance. This can lead to fatal electric shocks and/
or fires.
-
Never operate the appliance when it or its power
cable are damaged.
WARNING Electrocution
In the event of damage to the power cable this must
always be replaced by a qualified electrician authorised
by the manufacturer, using original spare parts.
WARNING Burns
Never operate this appliance...
-
in areas at risk from fire.
-
in rooms where the appliance is at risk of fire or
explosion as a result of chemicals, dust, gases or
vapours.
-
near pipes or receptacles that carry or contain flam-
mable or explosive materials.
-
if work such as laying tiles, sanding or sealing is
being carried out in the installation room.
-
if naphtha, sprays, floor polish or similar products
are handled.
-
Observe the minimum clearances. For this, see the
chapter Specification.
WARNING Burns
-
Never place any objects on top of the appliance.
Never lean any objects against it or place any ob-
jects between the appliance and the wall.
-
Never place any flammable, combustible or insula-
ting objects or materials, such as laundry, blankets,
magazines, containers with floor polish or naphtha,
spray cans or similar, near the appliance.
CAUTION Burns
Parts of the appliance can get very hot and may cause
burns. Particular caution is advised when children or
vulnerable persons are present.
CAUTION Burns
The grille also remains hot after the appliance is swit-
ched off.
-
Never touch the quartz tubes.
-
Never adjust the pivoting angle of the appliance in
use.
Never cover the appliance.
!
Material losses
Ensure that the power cable is never in contact with the
hot appliance, other parts or sharp edges.
2.3 Test symbols
See type plate on the appliance. The type plate is located at the
back of the appliance.
3. Appliance description
The appliance only warms the air slightly. It is only when it hits
objects or the human body that the IR radiation is converted into
heat. You will feel the heat after just a few seconds.
The appliance is made completely from stainless steel. The appli-
ance can be exposed to normal environmental influences.
4. Operation
4.1 Switching the appliance on
f
f
If not already in place, connect the power cable to the cable
with mains plug.
f
f
Start the appliance by pushing the power plug into its socket.
4.2 Switching the appliance off
f
f
Switch off the appliance by pulling the power plug from its
socket.
5. Cleaning, care and maintenance
!
Material losses
Never spray the appliance with water. Never immerse the
appliance in water.
Never touch the quartz rods with fingers, otherwise spots
could form or the quartz rods could be damaged.
f
f
Isolate the appliance from the power supply and let it cool
down.
f
f
A damp cloth is sufficient for cleaning the casing. Never use
abrasive or corrosive cleaning agents. Go over with a soft
cloth.
f
f
Regularly clean the reflector through the grille using a paint
brush.
Let a contractor clean the reflector if it is heavily so-
iled to retain the full level of heat radiation of this appliance.
The heating tube (gold tube) has a maximum service life of approx.
5000 hours. It is subject to the operating conditions, such as the
relative humidity, switching frequency and the orientation of the
radiant heater.
6. What to do if...
... you notice a smell
- For a short time after first taking the appliance into use as
well as after longer breaks in use, a smell may develop.
... the appliance does not radiate heat
- Check whether the fuses/MCBs have blown/tripped or are
faulty.
If you cannot remedy the fault, notify your heating contractor. To
facilitate and speed up your request, provide the number from the
type plate (000000-0000-000000).
