Stid SPECTRE NANO Installation Procedure Download

Page: 5 / 13

SPECTRE nano
UHF & Bluetooth

reader

Installation procedure

SPECTRE nano
Lecteur UHF & Bluetooth

Notice d’installation

SPECTRE nano
Lector UHF y Bluetooth

Manual de instalación

sur

Ed. 06/01/2022

Configuration SNA Read only & OSDP

™

The reading mode (UHF or/and Bluetooth

), the communication protocol

…

are configurable with the ULTRYS software or when the reader is ordered.

▪

TTL protocols (Wiegand & ISO2):

ISO2 (Clock & Data) - Decimal (7 bytes max)

Wiegand 26-bit

….

Wiegand with LRC - Hexadecimal (16 bytes max) + LRC

Wiegand without LRC - Hexadecimal (16 bytes max).

▪

Serial protocols (RS232 & RS485): The structure of the frame can be configured with the following optional parameters (in grey):

1 byte

X bytes

1 byte

STX

Lane number

ID-Tag

Tag Data*

LRC

ETX

0x02

0x01

0x0y nn…..nn

0x0D

0x0A

0x03

STX+ETX: add 0x02 (STX) and 0x03 (ETX) at the start /end of frame - CR/LF: Carriage Return (0x0D + 0x0A) configurable separately

LRC: Checksum (XOR of all previously bytes except STX) - Data sent in: decimal or hexadecimal

ASCII: if this option is activated, the data will be sent in ASCII mode (data size will be doubled)

Non-significant zero: complete the tag data with not significant 0 to obtain the defined data size

Lane no. fixed to 01 (SNA has only 1 lane)

▪

OSDP™ protocol (RS485: 7OS): refer

to Spec_Protocole_7OS_OSDP_UHF-US.pdf.

Start Sequence SNA Read only

& OSDP™

When the reader is switched on, the white LED lights up. Reader initializing.
After initializing, the reader will look for a SCB/OCB UHF configuration card for about 15 s, Blue LED lights up.

If a configuration card is detected: the LED displays orange while reading data, then LED and buzzer gives the followings indications:

•

3 GREEN flashes (500ms ON; 500ms OFF) + buzzer at the same time: SCB/OCB UHF is taken into account.

•

3 RED flashes (500ms ON; 500ms OFF) + buzzer at the same time: the regulation (region) of the SCB/OCB UHF does not match to the regulation of the reader.

•

3 PURPLE flashes (500ms ON; 500ms OFF) + buzzer at the same time: the protection code of the SCB/OCB UHF does not match to the reader protection code.

•

5 RED flashes (500ms ON; 500ms OFF) + buzzer at the same time: the SCB/OCB UHF is not for SNA reader.

•

no LED/Buzzer: the SCB/OCB UHF version does not match with reader version and the configuration card is not taken into account.

The end of the start sequence is indicated by the flashing of the reader LED white 3 times and buzzer sounds 3 times at the same time as the LED

Start Sequence SNA Read & Write

When the reader is switched on, the white LED & buzzer lights up. Reader initializing (a few seconds) then everything goes out. The reader then waits for commands.

Coming from the factory, the SPECTRE nano is compatible with SSCP

v1 and v2 communication protocols. You must use the Authenticate command to define the

desired communication protocol.

All commands are available in the SSCP

protocol specification:

Spec_Protocole_SSCP_UHF_ACCESS_V1.2_FR.pdf.

Declaration of Compliance

STid declares that the SNA-R4x-A & SNA-R5x-A reader is compliant to the fundamental requirements of Directive RED 2014/53/EU and Directive RoHs 2011/65/EU
and Commission Delegated Directive 2015/863/EU. A copy of our declaration is available upon request send to

[email protected]

This device complies with Part 15 of the FCC rules and with Innovation, Science and Economic Development Canada’s license

-exempt RSS(s). Operation is subject

to the following two conditions:

1) This device must not cause harmful interference.

2) This device must accept any interference received, including interference that may cause undesired operation.

Note: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void

the user’s authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can emit radio frequency energy and,
if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the distance between the equipment and receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for assistance.

This equipment complies with FCC’s

and ISEDC's radiation exposure limits (using RSS-102 rules) set forth for an uncontrolled environment under the following

conditions:

This equipment should be installed and operated such that a minimum separation distance of 34 cm / 13.39 in

is maintained between the radiator

(antenna) and the

user’s/nearby person’s body at all times.

The transmitter must not be co-located or operated in conjunction with any other antenna or transmitter.