Stewart MacDonald ALL AMERICAN Assembly Instructions Manual Download Page 4

Page: 4 / 12

stewmac.com

page 4 of 12

R2, R3

Resistors (100 kΩ)

Brown Black

Black Orange Brown

Yellow Purple Black

Gold Brown

Green

Blue

Black

Black Brown

Resistor (560 Ω)

Resistor (47 Ω)

Brown Green Black Brown Brown

R13

Resistor (1.5 kΩ)

JHS Pedals Kit

For Stew Mac

DC Jack

All American

InJ

T
S

R1
R2
R3

R17

R13

R14

R15

R5
R6

R11

OutJ

P78867

R10

R12

C12

C15

R16

C13

C11

C14

R4, R6, R14

Resistors (1.0 MΩ)

Brown Black

Black Yellow Brown

Brown Black

Black

Red

Brown

R15

Resistor (10 kΩ)

R5, R9, R11

Resistors (1 kΩ)

Brown Black

Black Brown Brown

Brown Black

Black Brown Brown

R17

Resistor (1 kΩ)

Step 1: Install thirteen resistors

Resistors have a low profile, sitting closer to the board than taller components,
so install them first. Their locations are marked with numbers on the board.

Resistors are not polarized, so it doesn’t matter which lead goes in which
eyelet. They can be installed in either direction.

Summary of Contents for ALL AMERICAN













Search results

Summary of Contents for ALL AMERICAN

Reviews:

Related manuals for ALL AMERICAN

Brands by name

Popular brands

Stewart MacDonald ALL AMERICAN, Assembly Instructions Manual

Search results

Summary of Contents for ALL AMERICAN

Reviews:

Related manuals for ALL AMERICAN

Brands by name

Popular brands