background image

Product Support

LiddleRod™ © 2010 Stevens AeroModel all rights reserved. 

Page 2 of 14

WARRANTY

Stevens AeroModel guarantees  this kit to be free from defects  in both material and workmanship at the 

date of purchase.  This warranty does not cover any component parts damaged by use or modification.   

In no case shall  Stevens  AeroModel’s  liability  exceed the original cost of the purchased kit.   Further, 

Stevens AeroModel reserves the right to change or modify this warranty without notice.

LIABILITY RELEASE

In that Stevens  AeroModel  has  no control  over  the final assembly or  material used for final assembly, 

no liability shall be assumed nor accepted for any damage resulting from the use by the user of the final 

user-assembled product.  By the act of using the user-assembled product, the user accepts all resulting 

liability.

If the buyer  is  not prepared to accept the liability associated with the use of this  product, the buyer is 

advised to return this kit immediately in new and unused condition to the place of purchase.

THIS PRODUCT IS NOT INTENDED FOR CHILDREN 12 YEARS OF AGE OR YOUNGER

WARNING:  This  product may contain chemicals known to the State of California to cause cancer and 

or birth defects or other reproductive harm.

PRODUCT SUPPORT

This  product has  been engineered to function properly  and perform  as  advertised with the suggested 

power  system  and  supporting  electronics  as  outlined  within  this  product  manual.    Product  support 

cannot  be  provided  nor  can  Stevens  AeroModel  assist  in  determining  the  suitability  or  use  of 

electronics, hardware, or power systems not explicitly recommended by Stevens AeroModel.

For  product assembly  support, replacement parts,  hardware, and electronics  to  complete  this  model 

please contact Stevens AeroModel on-line at 

www.stevensaero.com

.

Stevens AeroModel

PO Box 15347 - Colorado Springs, CO 80935 - USA

719-387-4187 - www.stevensaero.com

Summary of Contents for LiddleRod 2.4














Reviews: