Sterling Models Kingfish Sailboat Assembly Manual Download Page 13 | Manualshive

Page: 13 / 17

Sterling Models Kingfish Sailboat Assembly Manual Download Page 13

Page

13

Step 12

–

Standing Rigging

Insert end of anchor through hole in anchor stock and cement together at right angle. Paint black. Tie
chain to end hole in anchor with thin black thread (not supplied). Cement anchor, and fasten chain to
deck as shown in TOP VIEW. Standing rigging is installed in this step, using black line, referring to Figure
15. Special rigging line is nylon and is prone to unravel when cut with a knife. It is recommended that
line be cut with a hot soldering iron which will fuse the ends. Rigging lines should be installed snug
enough to be straight and care must be taken that mast is not pulled out of line. Any bend in the birch
dowel mast can be straightened by tightening the proper line. The backstay is tied to the top of the mast
then tied to the screw eye on the rear of the deck. Shroud lines are installed by tying from the screw
eyes on the blocks, through the top hole in the mast, and tied to screw eyes on the opposite side. The
bobstay is tied from the front of the bowsprit to the screw eye on the front of the hull.

Figure 15

«
...
11
12
13
14
15
...
»

Summary of Contents for Kingfish Sailboat


















Reviews:

No comments