Steris VividImage MON-STE42HD Operation Manual Download Page 13

Page: 13 / 19

Document #

13 of 19

Revision Date

82070-248, Revision A

1/19/2009

Language Setting (English Only)

Using Side Controls of monitor:

Press “

MENU

” to enter Main Menu.

Press “

” 3 times and press the “

Enter

” to enter item

Press “

▽

” to select sub-item (English only)

Press “

Enter

” when finished adjusting

Press “

MENU

” to exit the item

Using Remote Control:

Press “

MENU

” ->”

ENTER

” to enter picture setting

Press “

” or “

” to select Main Menu

Press “

ENTER

” to enter item

Press “

▽

” to enter sub-item (English only)

Press “

ENTER

” when finished adjusting

Press “

EXIT

” to exit the item

Default Setting

Using Side Controls of monitor:

Press “

MENU

” to enter Main Menu

Press “

/+”

4 times to select original default setting

Press “

Enter

” to enter item

Press “

▽

” to select sub-item (factory reset, set display, etc.)

Press “

” or “

” to adjust

Press “

Enter

” when finished adjusting

Press “

MENU

” to exit the item

Using Remote Control:

Press “

MENU

” to enter Main Menu

Press “

” or “

” to select Main Menu

Press “

ENTER

” to enter item

Press “

▽

” to enter sub-item (factory reset, set display, etc.)

Press “

” or “

” to adjust

Press “

ENTER

” when finished adjusting

Press “

EXIT

” to exit the item

Input Signal Selection

Using Side Controls of monitor:

Press the “

MENU

” to enter Main Menu

Press “

▽

” to enter

Press “

” or “

” to select single input

Press “

Enter

” when finished adjusting

Using Remote Control:

Press the “

MENU

” to enter Main Menu

Press “

▽

” to enter

Press “

” or “

” to select single input

Press “

Enter

” when finished adjusting

Summary of Contents for VividImage MON-STE42HD




















Search results

Summary of Contents for VividImage MON-STE42HD

Reviews:

Related manuals for VividImage MON-STE42HD

Brands by name

Popular brands

Steris VividImage MON-STE42HD, Operation Manual

Search results

Summary of Contents for VividImage MON-STE42HD

Reviews:

Related manuals for VividImage MON-STE42HD

Brands by name

Popular brands