background image

Updating Firmware_____________________________________________________________________________________18

12. Updating Firmware

The day may come you want to update your edition or try out another. Your Synth Programmer offers a 

firmware update mode for this. After entering this mode you just send a firmware-file into the controllers Midi IN

2 jack. The firmwares in SysEx-format are all compatible with your Programmer and freely available on our 

website. You can dump them with any standard SysEx dump tool of which several are available as freeware for 

different operating systems. An exmaple for PC is 'MidiOX', for the Mac you could use 'SysEx Librarian'.

The technical part:

 

Switch off the Stereoping Programmer

Connect 

MIDI OUT

 of your Midi-Interface directly to the jack 

MIDI 2 IN

 of the Programmers using a short

cable of good quality

There are some preferences in most SysEx-Dump Programs like 'Delay between Buffers' or 'Delay after 

F7'. Please choose something around 100mS (Milliseconds) here.

Hold MOD and power up your Programmer. The Display should read 'BOOTLOADER'

Load the new Firmware into your SysEx-Dump Program and send it out

The display shows OS-Version and progresst. After about 2 minutes the Programmer restarts

If you will get an error on the screen please try another cable or increase the delay mentioned above.

The firmware update erases all E-Patches!

Synth Programmer for Waldorf Pulse – Operation manual V 1.0 – 01/2018

© Stereoping Germany, Meschede 2018

Summary of Contents for Waldorf Pulse 1





















Reviews: