manualshive.com logo in svg

Stereoping SPRING REVERB, Building Instructions

Share
Download
Stereoping SPRING REVERB Building Instructions Download Page 18

This photo showns another module but the principles are the same. If you look 
straight from above through the pot-row, all axis should match in a row. Before you 
solder the pots, please check multiple times thoroughly that 

•

all pots are in a row 

•

all pot-bodies are lying flat on the pcb

•

all metal clamps are snapped in perfectly

First solder one or more pins and check AGAIN from all sides. It might help to attach 
the frontplate to have an overall look. If you are perfectly sure all pots are straight, 
solder the metal clamps to give the pots a mechanical strength and do not be stingy 
with solder.

All parts should have found their places on the pcb now and in front of you there are 
just 3 ICs remaining (apart from the redundant resistor R4). Time to get the module 
into operation.

Building instructions 'Eurorack Spring Reverb'

V1.0 - 06.2014

© Stereoping Germany, Hattingen 2014

Summary of Contents for SPRING REVERB




























Reviews:

No comments

Brands by name

Popular brands

Load more brands