STEMMER IMAGING GARDASOFT PP8 Series User Manual Download Page 22 | Manualshive

Page: 22 / 36

background image

WWW.STEMMER-IMAGING.COM

PP8xx LED Controller - User Manual

8

Ethernet address

You may need to ask your network administrator for advice about setting
up the Ethernet connection.

The application note APP923 – Troubleshooting Ethernet problems is
available from

www.gardasoft.com/Downloads

.

The Ethernet set up of the PP82x is not affected by cold-booting the
controller.

8.1

IP address

The PP82x needs an Internet Protocol (IP) address to communicate over
Ethernet. There are two ways to get an IP address; either programmed
into the unit or using DHCP.

For DHCP mode, the PP82x acquires its IP address, subnet mask, and
gateway address from the DHCP server. Otherwise the PP82x has a fixed
IP address, subnet mask, and gateway address.

DHCP mode or the IP address can be set or read using the
GardasoftMaint program available from

www.gardasoft.com/Downloads

.

The GardasoftMaint window is shown below:

—

24

—

WWW.STEMMER-IMAGING.COM

«
...
20
21
22
23
24
...
»

Summary of Contents for GARDASOFT PP8 Series





































Reviews:

No comments

Related manuals for GARDASOFT PP8 Series

Brand: Nelson Pages: 19

Brand: C-TEC Pages: 2

Brand: Jeep Pages: 32

Brand: Accel Pages: 8

Brand: Saga Pages: 9

Brand: Laars Pages: 28

Brand: Lamtec Pages: 22

Brand: Zamel Pages: 2

Brand: Zamel Pages: 2

Brand: Zamel Pages: 2

Brand: B&G Pages: 19

Z1000 CIMR-ZU*A Series

Brand: YASKAWA Pages: 340

Brand: ETC Pages: 8

Brand: Texas Instruments Pages: 27

TempMaster M2 Plus Series

Brand: Mold-Masters Pages: 2

Brand: Spirax Sarco Pages: 24

Brand: Trinamic Pages: 30

Brand: Hearth Products Controls Pages: 5

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands