Stelpro STZW402+ User Manual Download Page 5 | Manualshive

Page: 5 / 16

background image

040D05A_INS1215

5

6. Pass the wires from the wall through the hole at the base of the mounting base and connect them

using the supplied solderless connectors. When making the connection with aluminum wire,

make sure that you are using connectors identified CO/ALR. Please note that the thermostat

wires do not have polarity. Therefore, the way they are connected is not important.

2-WIRE INSTALLATION

4-WIRE INSTALLATION

«
...
3
4
5
6
7
...
»

Summary of Contents for STZW402+

















Reviews:

No comments

Related manuals for STZW402+

THERMO-FIXX 0123 Series

Brand: KWB Pages: 24

Brand: Trane Pages: 20

Brand: OJ Electronics Pages: 22

Brand: Cadet Pages: 2

Brand: Braun Pages: 11

Brand: Coati Pages: 32

Brand: Gima Pages: 2

Wi5 Wi-Fi Series

Brand: Living Heat Pages: 4

Brand: Vava Pages: 5

Brand: Mobi Technologies Pages: 8

Brand: nubeca Pages: 24

Brand: Venstar Pages: 29

Brand: Carrier Pages: 8

Brand: Mi-Heat Pages: 12

Brand: domat Pages: 8

Brand: AEG Pages: 4

Brand: AEG Pages: 112

Brand: AEG Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands