Stelpro STZB402 Plus User Manual Download Page 5 | Manualshive

Page: 5 / 15

background image

042D07_INS0616

5

6. Pass the wires from the wall through the hole at the base of the mounting base and connect them

using the solderless connectors supplied. When making the connection with aluminum wire,

make sure that you are using connectors identified CO/ALR. Please note that the thermostat

wires do not have polarity. Therefore, the way they are connected is not important.

2-WIRE INSTALLATION

4-WIRE INSTALLATION

«
...
3
4
5
6
7
...
»

Summary of Contents for STZB402 Plus
















Reviews:

No comments

Related manuals for STZB402 Plus

Brand: Fantini Cosmi Pages: 8

Brand: Salus Pages: 28

Brand: Malmbergs Pages: 2

Premium Mini D2270

Brand: Daikin Pages: 44

Brand: Namiba Terra Pages: 24

Brand: Xavax Pages: 39

Brand: tio Pages: 2

tekmarNet2 Thermostat 530

Brand: Tekmar Pages: 20

AirConService TM-84N

Brand: Waeco Pages: 184

Brand: Danfoss Pages: 2

Brand: Trotec Pages: 142

Brand: General Pages: 8

Brand: GSI Group Pages: 22

ECL Comfort 310, P318

Brand: Danfoss Pages: 16

Brand: BURNHARD Pages: 76

Brand: Danfoss Pages: 2

Brand: LifeSource Pages: 4

Brand: Fantini Cosmi Pages: 52

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands