Stel 601267000L, Instruction Manual

Page: 18 / 38

6943100020
18
PRE-HEAT
For alluminium 8mm thick is recommended a pre-
heating of the material .
FUNCTION OF STORING AND
LOADING WELDING
PARAMETERS (JOB MODE)
Function active for all welding modes
This function allows you to store and load at any
time all the settings made on the power source. It
is possible to save 30 welding parameters settings)
STORING WELDING SETTINGS
1) Press the button JOB LIST (ref.8) to go in the
JOB LIST page.
2) Using the button ↑ (rif.9) ↓ (rif.10) or the
encoder
V/SET
(ref.11) select the number of the
programme in which you want to save the welding
parameters.
3) Press and hold the
SAVE button (ref.8) for about
3 seconds until you will hear the sound of the
buzzer.
4) When the parameter will be saved you will come
back immediately on the main page and it is
possible see on the frame JOB the JOB number
you are using.
ATTENTION : THE PARAMETERS SAVED FROM
THE POSITION 1 TO 12 ARE PROTECTED; SO
WHEN YOU WILL RECALL THEM , THEY WILL
BE BLOCKED.
TO REMOVE THE PROTECTION OF THE
PARAMETER AND COME OUT FROM ANY JOB
CONDITIONS PRESS THE BUTTON
JOB LIST
(ref.8) TO GO IN THE JOB LIST page AND
PRESS AND HOLD THE BUTTON
SELECT
MODE (rif.6) FOR ABOUT 5 sec.
LOADING STORED WELDING PROGRAMS
1) Press the button JOB LIST (ref.8) to go in the
JOB LIST page.
2) Using the button ↑ (rif.9) ↓ (rif.10) or the
encoder
V/SET (ref.11) select the number of the
programme that you want recall.
3) Press and hold the
RECALL button (ref.7)
for about 3 seconds until you will hear the sound of
the buzzer.
4) After the recalling you will come back
immediately on the main page and it is possible
see on the frame JOB the JOB number you are
using.
NOTE :
The symbol “
*
“ ( asterisk ) means the JOB in use.
The symbol “
*
“ ( asterisk flashing ) means the
JOB is modified from the original.
TRIGGER JOB FUNCTION
In the first three position of JOB LIST is possible to
activate the TRIGGER JOB FUNCTION
This function allows to recall one of the first three
parameter of the JOB LIST with a quick pressure
of torch button.
For recall these parameters they must have a Pre
Gas time of 0,3 sec or more.
SCREENS DESCRIPTION
MIG SETUP
WATER COOLER UNIT
There is the possibility to connect a water cooling
unit as optional, the specifications for connections
will be provided with the kit.
For activate the WATER COOLER press the
SETUP button (ref.10) few times to go in the MIG
SETUP page.
Press the button
MODIFY (ref.8) and with the
button
SELECT
(ref.8) position the arrow near the
setting Water Cooler: ON - OFF
Then press the button
CHANGE (ref.9) to enable
or not the Spool gun torch.
Now press the button
V
(ref.10) to confirm the
choice.
If the Water Cooler is selected on the main screen
appears the symbol of water cooling. The water
cooler will be activated by the machine only during
the welding.
SETTING UNIT MEASURING WIRE SPEED
There is the opportunity to set the wire speed in
m/min or ipm.
Press the
SETUP button (ref.10) few times to go in
the MIG SETUP page.
Press the button
MODIFY
(ref.8) and with the
button SELECT (ref.8) position the arrow near the
setting Unit: m/min – ipm
Then press the button
CHANGE (ref.9) to select
between m/min or ipm.
Now press the button
V (ref.10) to confirm the
choice.
On the main screen is possible to see the wire
speed in ipm ( minimum 055 , maximum 629 ) .
The thickness will be also in inches .