background image

INTRODUCTION 

Please read all material carefully prior to installation. If you need additional assistance, contact your 

Steinway Lyngdorf representative or email [email protected]

 

COMPLIANCE 

WEEE 

The European Parliament and the Council of the European Union have issued the Waste Electrical 

and Electronic Equipment Directive. The purpose of the Directive is to prevent waste of electrical and 

electronic equipment and to promote reuse, recycling, and other forms of waste recovery. Steinway 

Lyngdorf products and the accessories packed with them are subject to the WEEE Directive. Please 

dispose of any waste materials in accordance with your local recycling regulations. Products and 

equipment which must be collected for reuse, recycling, and other forms of recovery are marked with 

the icon of the crossed-out waste receptacle.  

 

 

 

 

 
FCC 

Steinway Lyngdorf products and accessories comply with parts 15 and 68 of the FCC rules. Operation 

is subject to the following two conditions: (1) this device may not cause harmful interference; and (2) 

this device must accept any interference received, including any interference that may cause 

undesired operation. Changes or modifications not expressly approved by the party responsible for 

compliance could void the user’s authority to operate the equipment. Equipment marketed to a 

consumer must be capable of complying with the necessary regulations in the configuration in which 

the equipment is marketed. 

 

 
 
 

 

 

 

Summary of Contents for M






















Reviews: