Stefan Mayer Instruments AM502 Series Instruction Manual Download Page 8

 

 
 

 
 

 

 
 

 

Some views do not offer an edit mode (for example when the software version is shown). In some 
other views the (OK) key will start an immediate action (for example triggering the autotuning). Few 
situations require a longer pressing of a key. However, everything will be explained in this manual 
later.  

4.2 Measurement Display 

The various display options are explained in the following paragraphs. 
 

Display Variant 1 

– Magnetic Field Strength and Signal Quality 

 
Besides  the  value  of  the  magnetic  field  strength,  an  indication  about  the  logging  activity  will  be 
displayed in the upper right corner (LOG=Logging without GPS; G-LOG=Logging with GPS): 
 

 
 
 

 
In the lower right corner, the signal strength of the precession signal is displayed. The first number 
shows the signal strength directly after the polarization phase, while the second number indicates 
the strength after completion of the frequency measurement. These numbers are unit-less guidance 
values to see if the measurements are reliable or disturbed. They can be compared only if the tuning 
setting is not changed. 
 

Display Variant 2 

– Bar Graph  

 

This view shows a simple bar graph visualizing either the difference to a reference value (will be 
set  by  a  3  sec.  long  press  of  the  (OK)  key,  see  below)  or  the  difference  to  the  previous 
measurement. The lower right corner shows the numerical difference, respectively. 
 

 
 
 

 
In the upper right corner, the logging indicator will be shown, as mentioned above. If no logging is 
active, the first signal amplitude value (the one directly after the polarization) will be shown. 
 
If the value range of the selected bar graph (see below) is exceeded, the symbols "<" or ">" will be 
shown. The value in the lower right corner will still show the correct difference. 
 
 
 
 
 
 

TUNING 
47500 nT 

 (OK) 

47500 nT 
< - + > 

(OK) 

(+)

 Increment the Value (for example to 47750)

 

 

 

 

(-)

 Decrement the Value (for example to 47250)

 

Display-Mode

 

Edit-Mode

 

47965.0 nT G-LOG 
         071/056  

47521.3 nT G-LOG 
  ======   -12.3 

Summary of Contents for AM502 Series


















Reviews: