Steelcase Translations Open Workstation Installation Manual Download Page 3 | Manualshive

Page: 3 / 11

background image

3/4” SCREWS

3/4” SCREWS

3.

Lay top panel in place upon angle brackets and secure

each bracket with (4) 3/4” screws.

4.

Install center support as shown.

PRY BAR

1” WRENCH

OPEN-OFFICE WORKSTATION

TYPICAL INSTALLATION

1.

Begin installation by installing levelers and then leveling

End Unit. Leveler adjustment can be

aided by use of pry bar to take

weight off leveler while

adjustment is made.

LEVELER

Assembly Directions

REV A

Y9501911

Steelcase

Page

3 of 11

«
1
2
3
4
5
...
»

Summary of Contents for Translations Open Workstation












Reviews:

No comments

Related manuals for Translations Open Workstation

Brand: KANYON Pages: 3

Brand: Zenox Pages: 2

Brand: pakoworld Pages: 2

Brand: B&Q Pages: 4

Brand: B&Q Pages: 2

Brand: Badger Basket Pages: 6

Brand: ZIMSTONE Pages: 5

Brand: Happy Babies Pages: 7

Brand: Safco Pages: 7

Brand: Naos Pages: 4

Brand: RAL Pages: 2

Brand: HAMPTON BAY Pages: 16

Brand: Saber Compact Pages: 6

Brand: Velux Pages: 5

VELUX INTEGRA Solar SST

Brand: Velux Pages: 15

Brand: Walker Edison Pages: 10

Main station base 7756

Brand: Safco Pages: 2

SYNERGY SYSTEM SLC20

Brand: Salamander Designs Pages: 5

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands