Table of Contents
®
Page 2 of
71
1317809001
Rev A
Title page..............................................................................1
Table of contents..................................................................2
Important safety instructions................................................3
Power source/Glides/Drawer removal..................................5
Remove weight cover panels...............................................6
Ganging Light Seal...............................................................7
Ganging brackets.................................................................8
Attach end skins..................................................................9
Install lower column stabilizing bracket..............................10
Cable Routing Overview.....................................................12
Route power.......................................................................13
Power bracket installation..................................................14
Remove column lid and lower shroud................................15
Run wires through column................................................ 16
Rout power through column and carrier............................ 17
Install column wire cover....................................................18
Level and add counterweights...........................................19
Install foundation to floor....................................................21
Reinstall counterweight coverplates..................................22
Attach remaining outerskin................................................23
Install touch latch...............................................................24
Attach drawer....................................................................25
Install drawer lock.............................................................26
Plastic lock plug removal/Lock cylinder installation..........27
Front removal of lock cylinder...........................................28
Attach drawer panel..........................................................29
Level foundation/center column........................................30
Install upper column stabilizer bracket..............................31
Attach shroud to column...................................................33
Attach column lid...............................................................34
Collab table: lay P.E.T. in position.....................................35
Collab table: attach cantilever...........................................36
Collab table: use set screws to level.................................37
Personal table: lay P.E.T. in position.................................38
Personal table: attach cantilever.......................................39
Personal table: use set screws to level.............................40
Attach power box to cantilever..........................................41
Collab table: subtop to cantilever......................................42
Personal table: subtop to cantilever..................................43
Perpendicular: modesty panel bracket..............................44
Perpendicular: modesty panel..........................................45
Attach worksurface to cantilever.......................................46
Attach power grommets....................................................47
Attach c-clamp brackets....................................................48
Secure power box in cantilever.........................................49
Attach up/down lever to worksurface and power...............50
Attach P.E.T. to underside of worksurface.........................51
Attach final coverplate.......................................................52
Tower and shroud installation............................................53
Attach Z brackets to bottom weldment..............................54
Attach RH upright weldment..............................................55
Attach LH upright weldment..............................................56
Attach upper weldment.....................................................57
Attach center column(s)....................................................58
Attach shelves to column..................................................59
Attach tower to foundation................................................60
Place topskin on foundation..............................................61
Attach shelf light................................................................62
Half shroud installation......................................................63
Full shroud installation......................................................64
Monitor installation............................................................65
Attach shroud cover..........................................................66
Wall hanging application...................................................67
Mounting plate / wall mount..............................................68
Center of gravity location and total weight........................69
Attach column to wall mount.............................................70
Attach shroud to column...................................................71
Summary of Contents for Mackinac
