Steelcase eno play Installation And Operation Manual Download Page 8 | Manualshive

Page: 8 / 23

background image

ēno play

Install the driver packs

Locate and have ready to use:

•

driver packs (x2)

•

alcohol wipes (x2)

•

driver pack mounting template

•

tape

To install the driver packs:

1. Slide the driver pack mounting template to the upper left corner of whiteboard and tape it in

place.

Note

: The template has a front and back side. Be sure to use the template front in the upper

left corner.

8 of 23

2002480-001 Rev D

Installation and Operation Guide

«
...
6
7
8
9
10
...
»

Summary of Contents for eno play
























Reviews:

No comments

Related manuals for eno play

Brand: Campbell Pages: 46

Brand: V-ZUG Pages: 12

Brand: K&M Pages: 9

Brand: Panasonic Pages: 6

Brand: Panasonic Pages: 3

ECONAVI CZ-CENSC1

Brand: Panasonic Pages: 8

Brand: Panasonic Pages: 9

AR42P9W - Plasma Panel anti-glare Filter

Brand: Panasonic Pages: 5

Brand: Tamron Pages: 3

Brand: DataSafe Pages: 4

Brand: AA Products Pages: 6

Brand: iDataLink Pages: 30

Brand: Natibaby Pages: 24

Brand: Narvitech Pages: 12

Brand: Parker Pages: 2

Brand: Park Tool Pages: 2

Brand: ParaZero Pages: 17

Brand: Vega Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands