Steelcase 462 Leap V2 Disassembly Download Page 7 | Manualshive

Page: 7 / 20

background image

Page 7 of 20

939546225 Rev A

®

Bins for components

removed

Acetal

Nylon

Steel

Scrap

Urethane

2.

Remove two (2) height adjustment

bearings.

3.

Use a T-20 bit to remove four (4)

screws under arm cap. Lift and remove
outer arm cap. Pull arm cap skin off arm
cap. Scrap remaining molded foam
assembly.

4.

Use a T-20 drive bit to remove

two(2) screws and pull off lower
arm cap support, rear bearing, front
bracket, spring and washer.

LOWER ARM

CAP SUPPORT

HEIGHT ADJUSTMENT

BEARING

3

2

4

FRONT

BRACKET

WASHER

SPRING

REAR

BEARING

MOLDED FOAM

ASSEMBLY

ARM CAP SKIN

«
...
5
6
7
8
9
...
»

Summary of Contents for 462 Leap V2





















Reviews:

No comments

Related manuals for 462 Leap V2

Brand: Naterial Pages: 16

Brand: W.Schillig Pages: 13

Brand: Gazelle Pages: 6

Brand: Easy Track Pages: 2

Brand: East West Furniture Pages: 4

Brand: East West Furniture Pages: 4

Brand: East West Furniture Pages: 5

Brand: Jar Furniture Pages: 6

Brand: Varier Pages: 3

Brand: HAG Pages: 21

Brand: HAG Pages: 2

Brand: OAKWORKS Pages: 20

Brand: Made Pages: 8

Brand: PAIDI Pages: 4

Brand: Safco Pages: 3

Brand: Zenox Pages: 2

Brand: Varier Pages: 3

Office Port 408293

Brand: Sauder Pages: 36

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands