Continued on Next Page
SB-SC-TCG2/10W3v3 INSTR_SKU# 011323
s t e P 1 5
C o n G R a t u l a t I o n s !
You have completed the installation for this model!
Enjoy your new Stealthbox®!
Please refer to the Power Recommendation section for an
amplifier recommendation and basic set-up help.
s t e P 1 4
From inside the fender well, place a 3/8” x 2” Fender Washer,
a 3/8” x 1-1/4” Fender Washer, , and a 3/8” Split Lock Washer
over the 3/8” - 16 x 2-1/2” Hex Bolt, and firmly tighten.
Reinstall the woofer.
s t e P 1 3
Attach the speaker cable to the Stealthbox®, and position
the enclosure back into the vehicle, aligning the hole in the
side panel with the hole in the enclosure. Put a 3/8” x 1-1/4”
Fender Washer on the 3/8” - 16 x 2-1/2” Hex Bolt, and pass
the bolt through the holes in the enclosure, the Spacer, the
side panel, and the fender well.
Page 3 • JL Audio, Inc 2011
I n C l u d e d H a R d W a R e
(1) 3/8” - 16 x 2-1/2 Hex Bolt (2) 3/8” x 1-1/4” Fender Washer (1) 3/8” Split Lock Washer
(1) 3/8” x 2” Fender Washer (1) 3/8” -16 Hex Nut (1) Spacer
s P e C I F I C a t I o n s
Enclosure Type:
Acoustic Suspension (sealed)
Driver Type:
10W3v3-2
Nominal Impedance:
2 ohms
Continuous Power Handling:
500 watts
P o W e R R e C o m m e n d a t I o n
JL Audio recommends high quality amplifiers such as the JL Audio XD300/1. The diagram below shows the
recommended crossover settings for the XD300/1. If another amplifier is being used, please reference this
illustration and use similar settings on that amplifier.
All JL Audio amplifiers are very versatile audio components. Please consult the owner’s manual for even more
detailed information about installing and tuning your amplifier.
C o n n e C t I o n s
Using quality power, signal and speaker wire is essential in ensuring the performance of your Stealthbox®.
JL Audio recommends using a 4 AWG power kit such as the XD-PCS4-1B for your Stealthbox® amplifier, other
kits are available should you be using more than one amplifier. Signal wire such as the JL Audio Premium
Audio Interconnect Cables should be used that will provide signal for both channels of the amplifier. JL Audio
reccommends using 12AWG speaker wire for subwoofers such as our XC-BCS12-25.
m I d / H I G H F R e q u e n C Y d R I v e R F I t m e n t
A variety of JL Audio coaxial and component systems will fit in the factory speaker locations of you vehicle.
Front Speaker Size / Location:
6 x 9”- Front Doors
Fits JL Audio Models:
TR690-TXi, C2-690txi
Rear Speaker Size / Location:
6-1/2”- Side Panel
Fits JL Audio Models:
TR650-CXi, C2-650x, C3-650, C5-650x, & ZR650-CSi
S T E P 1 2
Place the Spacer into the hole drilled in the side panel.
All specifications are subject to change without notice. “JL Audio®” and the JL Audio logo, “Stealthbox” and the Stealthbox logo are registered
trademarks of JL Audio, Inc. “Ahead of the Curve” and its respective logo is a trademark of JL Audio, Inc.
JLA-SKU# 94515 04.25.2009 • Printed in USA • ©2008 JL Audio, Inc. • U.S. PATENTS: #5,734,734 #5,949,898 #6,118,884 #6,229,902 #6,243,479
#6,294,959 #6,501,844 #6,496,590 #6,441,685 #5,687,247 #6,219,431 #6,625,292 #D472,891 #D480,709 Other U.S. & Foreign patents pending.
For more detailed information please visit us online at www.jlaudio.com.
(954) 443-1100
w w w. j l a u d i o . c o m
1 0 3 6 9 N O R T H C O M M E R C E P A R K W A Y • M I R A M A R , F L O R I D A • 3 3 0 2 5 • U S A
