background image

2

Manual Aiolos

Manual Aiolos

WARNING

        

WARNING:

  Read the ENTIRE instruction manual to become familiar with the features of 

the product before operating. Failure to operate the product correctly can result in damage to 

the product, personal property and cause serious injury. 

This is a sophisticated hobby product. It must be operated with caution and common sense and 

requires some basic mechanical ability. Failure to operate this product in a safe and responsible 

manner could result in injury or damage to the product or other property. This product is not in-

tended for use by children without direct adult supervision. Do not use with incompatible compo-

nents or alter this product in any way outside of the instructions provided by Gustav Staufenbiel 

GmbH. This manual contains instructions for safety, operation and maintenance. It is essential 

to read and follow all the instructions and warnings in the manual, prior to assembly, setup or 

use, in order to operate correctly and avoid damage or serious injury.

SAFETY PRECAUTIONS AND WARNINGS

As the user of this product, you are solely responsible for operating in a manner that does not 

endanger yourself and others or result damage to the product or the property of others. This 

model is controlled by a radio signal subject to interference from many sources outside your 

control. This interference can cause momentary loss of control so it is advisable to always keep 

a safe distance in all directions around your model, as this margin will help avoid collisions or 

injury.

Age Recommendation: Not for children under 14 years. This is not a toy.

• 

A lways keep a safe distance in all directions around your model to avoid collisions or injury. 

This model is controlled by a radio signal subject to interference from many sources outside 

your control. Interference can cause momentary loss of control. 

• 

Always keep aircraft in sight and under control.

•  Always operate your model in an open area away from cars, traffic or people.

• 

Avoid operating your model in the street where injury or damage can occur.

• 

Never operate the model in the street or in populated areas for any reason.

• 

Avoid operating your model in the street where injury or damage can occur.

• 

Never operate your model with low transmitter batteries.

• 

Always use fully charged batteries.

• 

Always remove batteries after use.

• 

Always let parts cool after use before touching.

• 

Carefully follow the directions and warnings for this and any optional support equipment 

(chargers, rechargeable battery packs, etc.) you use.

• 

Keep all chemicals, small parts and anything electrical out of the reach of children.

• 

Moisture causes damage electronics. Avoid water exposure to all equipment not specially 

designed and protected for this purpose.

• 

Never lick or place any portion of your model in your mouth as it could cause serious injury 

or even death.

Summary of Contents for Aiolos HSF0314083





















Reviews: