background image

2 / 8

 

符号说明

Explanation of the symbols

危险电压警告

  

Warning of dangerous voltages

危险区域警告

Warning of a hazard area

产品使用说明或技巧

Useful hint or tip

安全须知

Safety instructions

产品只能由具备相应技能或受过相应培训的专业人员,依照适用

安全法规进行装配或安装。

如您未遵守上述警告,则 Stäubli Electrical Connectors (Stäubli) 

不承担任何责任。

The products may be assembled and installed exclusively by 

suitably qualified and trained specialists duly observing all ap

-

plicable safety regulations�

Stäubli Electrical Connectors (Stäubli) does not accept any li-

ability in the event of failure to observe these warnings�

仅可使用 Stäubli 指定的组件和工具。自行装配时,切勿背离本手

册所述的制备及装配说明,否则  Stäubli  无法保证产品安全性或

产品性能达到官方技术参数。请勿以任何方式修改产品。

Use  only  the  components  and  tools  specified  by  Stäubli.  In 

case of self-assembly, do not deviate from the preparation and 

assembly instructions as stated herein, otherwise Stäubli can-

not give any guarantee as to safety or conformity with the 

technical data� Do not modify the product in any way�

可与 Stäubli 元件插合的非 Stäubli 原厂制造的连接器,在某些情

况下,某些制造商甚至将其描述为“与 Stäubli 兼容”,但该连接器

并不符合长期稳定安全的电连接要求,而且出于安全考虑,不得

与 Stäubli 元件插合在一起。因此,Stäubli 对因此类连接器(即未

经 Stäubli 批准)与 Stäubli 元件插合而造成的任何损失不承担任

何责任。 

Connectors not originally manufactured by Stäubli which can 

be mated with Stäubli elements and in some cases are even 

described as ”Stäubli-compatible” by certain manufacturers 

do not conform to the requirements for safe electrical connec-

tion with long-term stability, and for safety reasons must not 

be plugged together with Stäubli elements� Stäubli  therefore 

does not accept any liability for any damages resulting from 

mating such connectors (i�e� lacking Stäubli approval) with 

Stäubli elements� 

 

此处所述作业不得在带电或负载部件上进行。

 

The work described here must not be carried out 

on live or load-carrying parts.

 

电击防护必须通过最终产品(即正确组装的插头连接器)及

其用户来确保。

 

Protection from electric shock must be assured by 

the  end  product  (i.e.  by  the  correctly  assembled 

plug connector) and by its user.

 

禁止在负载下断开连接。允许带电时进行插拔操作。 

 

The  plug  connections  must  not  be  disconnected 

under load. Plugging and unplugging when live is 

permitted. 

  

每次使用连接器前,需提前检查外部是否有磨损(尤其是绝

缘层)。如有安全疑虑,必须咨询专业人员或更换连接器。

 Each time the connector is used, it should previously 

be inspected for external defects (particularly in the 

insulation). If there are any doubts as to its safety, a 

specialist must be consulted or the connector must 

be replaced.

 

带外壳应用的连接器的防水功能可参考相关产品的IP保护等

级。

 The plug connectors in the housing are protected 

from water in accordance with the IP protection 

class stated for the relevant product.

 

未插合的连接器必须防潮防尘。被污染的公母连接器不应插

合使用。

 Unmated plug connectors must be protected from 

moisture and dirt. The male and female parts must 

not be plugged together when soiled.

 

欲了解更多技术参数,请参阅产品目录。

  For further technical data please see the product 

catalogue.

Summary of Contents for KST6AR-W-N Series









Reviews: