background image

Handbook for the TRIUS SX-825      Issue 1 January 2015 

 

 

22 

 

Dear Observer, 

Thank you for purchasing a Starlight Xpress CCD Imaging System. We are confident that you will gain 
much satisfaction from this equipment, but please read carefully the accompanying instruction manual 
to ensure that you achieve the best performance that is capable of providing. 

As with most sophisticated equipment a certain amount of routine maintenance is necessary to keep the 
equipment operating at its optimum performance. The maintenance has been kept to a minimum, and is 
fully described in the manual. 

In the unfortunate instance when the equipment does not perform as expected might we recommend 
that you first study the fault finding information supplied. If this does not remedy the problem, then 
contact Starlight Xpress for further advice. Our message board service on the Starlight Xpress web site 
will often provide solutions to any problems. 

The equipment is covered by a 12-month guarantee covering faulty design, material or workmanship in 
addition to any statutory Consumer Rights of Purchasers. 

CONDITIONS OF GUARANTEE 

1) The equipment shall only be used for normal purposes described in the standard operating 
instructions, and within the relevant safety standards of the country where the equipment is used. 

2) Repairs under guarantee will be free of charge providing proof of purchase is produced, and that the 
equipment is returned to the Service Agent at the Purchaser’s expense and risk, and that the equipment 
proves to be defective. 

3) The guarantee shall not apply to equipment damaged by fire, accident, wear an tear, misuse, 
unauthorised repairs, or modified in any way whatsoever, or damage suffered in transit to or from the 
Purchaser. 

4) The Purchaser’s sole and exclusive rights under this guarantee is for repair, or at our discretion the 
replacement of the equipment or any part thereof, and no remedy to consequential loss or damage 
whatsoever. 

5) This guarantee shall not apply to components that have a naturally limited life. 

6) Starlight Xpress’s decision in all matters is final, and any faulty component which has been replaced 
will become the property of Starlight Xpress Ltd. 

 

For further info. or advice, please call: 

Mr Michael Hattey, 

Starlight Xpress Ltd., 

Unit 3, Brooklands Business Park, 

Bottle Lane, 

Binfield 

Berkshire, 

England.  RG42 5QX 

Tel: 01184026898 

Email: 

[email protected]

  

Web site: 

www.sxccd.com

  

 
 
 

Summary of Contents for TRIUS SX-825























Reviews: