background image

2

GENERAL SAFETY INFORMATION

This equipment is designed and sold for commercial use only, and is intended for use by personnel 
trained and experienced in its operation. This is not sold for consumer use in and around the home  
nor for use directly by the general public in food service locations. 

Before using your new equipment, read and understand all the instructions and labels associated  
with the unit prior to putting it into operation. Make sure all people associated with its use understand 
the units operation and safety before they use the unit. 

GENERAL INSTALLATION INFORMATION

The unit is shipped fully assembled and ready to plug into a standard outlet specified for its voltage  
and amp draw. If improper electrical supply can be determined through troubleshooting, contact 
a qualified electrician prior to using the unit. Removal or replacement of the power cord or plug will  
void the warranty. Should you require assistance, contact your local authorized service agent for any 
service or required maintenance.  

Level unit using the adjustable feet under the unit [there is approximately 0.5 (1/2) inch of adjustment]. 
Allow enough space around the unit for adequate ventilation. It is recommended that you leave a ten  
(10)

 

inch gap on the top for cleaning if the unit is to remain stationary. The sides and back of the unit

 

require no additional clearance.

Before using the unit for the first time, make certain to clean it properly. Refer to the "Cleaning Procedure"  
document for cleaning instructions. The inlet and outlet trays will also need to be placed on the unit prior to 
use. The out

let

 tray slides on the lip under and in front of the drum area and the inlet tray sits on a rod

resting against the stop pins.

 

ELECTRICAL CONNECTION

Before making any electrical connection to this unit, check that the power supply is adequate for the  
voltage, amperage, and requirements stated on the rating plate. RTW14E

A

 units will require a NEMA  

5-

20P

 receptacle. RTW

19

E

A

 units will require a NEMA 6-

15

P

 receptacle. Make certain to disconnect the

 

unit from the power source before installing or removing any parts. Be absolutely sure that the ground

 

connection for the receptacle is properly wired. Do not connect equipment to power without proper

 

ground connections. Improper grounding may result in personal injury or fatality.

DO NOT CUT OR REMOVE THE PLUG OR  

DO NOT IMMERSE OR LET THE UNIT STAND

GROUNDING PRONG FROM THE PLUG.  

IN WATER.

CONNECT UNIT INTO DEDICATED AC LINE 

DO NOT HOSE DOWN THE UNIT OR THE 

ONLY AS SPECIFIED ON THE DATA PLATE  

TABLE/COUNTER IF THE UNIT IS ON THE 

OF THE UNIT.

TABLE/COUNTER.

belt guide

belt roller

inlet tray

stop pin

place here

outlet tray

Summary of Contents for RTW14EA

























Reviews: