Page 3
INSTALLATION INSTRUCTIONS
1
• TORQUE WRENCH
• • • • • • • • • • • • • • • • • • •• • • • • • • • • • • • • •• • • • • • •
1
• 8MM HEX KEY SOCKET
• • • • • • • • • • • • • • • • • • •• • • • • • • • • • • • • •
• #2 CROSS-HEAD (PHILLIPS) SCREWDRIVER
• • • • • • • • •
1
1
• 6MM HEX KEY SOCKET
• • • • • • • • • • • • • • • • • • •• • • • • • • • • • • • • •
1
• 13MM SOCKET
• • • • • • • • • • • • • • • • • • •• • • • • • • • • • • • • •• • • • • • • • • • • •
1
• 5MM HEX KEY SOCKET
• • • • • • • • • • • • • • • • • • •• • • • • • • • • • • • • •
1
• 19MM OPEN-END WRENCH
• • • • • • • • • • • • • • • • • • •• • • • • • • • • •
1
• 4MM HEX KEY SOCKET
• • • • • • • • • • • • • • • • • • •• • • • • • • • • • • • • •
1
• 17MM OPEN-END WRENCH
• • • • • • • • • • • • • • • • • • •• • • • • • • • • •
1
• 3MM HEX KEY SOCKET
• • • • • • • • • • • • • • • • • • •• • • • • • • • • • • • • •
2
• 13MM OPEN-END WRENCH
• • • • • • • • • • • • • • • • • • •• • • • • • • • •
1
• 2.5MM HEX KEY SOCKET
• • • • • • • • • • • • • • • • • • •• • • • • • • • • • • •
REQUIRED TOOLS:
GENERAL NOTES:
•
Unless otherwise noted Loctite 242/243 or equivalent thread locker must be used on all threaded fasteners. (Do not
use thread locker when a Nyloc nut is used.)
•
All Star Trac Strength equipment MUST be secured to the floor using either 10mm or 3/8in. (grade 5 minimum) bolts.
To accommodate this there are four mounting points inside the weight stack and one in either of the small feet.
•
This Installation Instructions Manual must be used in conjunction with the equipment’s Owner’s Manual. The Owner’s
manual describes equipment setup and instructs members on how to use it correctly and safely.
•
The Abdominal Machine weighs approximately 260 Kg (573 lbs) when fully assembled and occupies an area 155 cm
wide by 108 cm deep. Star Trac recommends the addition of 1-2 people during assembly, and when moving the
equipment to its designated point of use.
Should any component not be present or if you have any operational questions, please refer to your owner’s manual or on
the web @
www.startrac.com
. Specifically refer to your Inspiration serial number and model number labeled on your
equipment.
THREAD LOCKER APPLICATION:
Clean all threads and holes, apply no more than 3-4 drops per bolt.
Thru Holes
Blind Holes
PACKAGING REMOVAL:
Carefully remove all packaging materials that wrap the equipment.
DO NOT USE A KNIFE OR BOX
CUTTER AS YOU MAY DAMAGE THE EQUIPMENT.
At this time remove any sub-components
from the pallet and set aside for later assembly.
• Torque all hardware to values as specified above, unless noted otherwise.
• See Page 11 of this manual for fastener sizing information; for reference only.
• Note: All torque values are in N-m unless otherwise stated.
26 to 30 (35 to 40)
1.75
10mm
9.5 to 12 (13 to 16)
1.25
8mm
4.5 to 6 (6 to 8)
1.25
6mm
Torque, N-m (lbs-ft)
Thread Pitch
Bolt Size
Metric Steel Bolts Torque Specifications
Summary of Contents for INSPIRATION STRENGTH IP-S6331
Page 1: ...ABDOMINAL MACHINE IP S6331 INSTALLATION INSTRUCTIONS ...
Page 10: ...Page 10 ...
Page 11: ...Page 11 ...
