Star Micronics TSP043E Series Hardware Manual Download | Manualshive

Page: 10 / 24

background image

- 6 -

3-2-3. RS-232C Cable

To connect an RS-232C cable, follow the procedure given below.

1) Make sure that the AC adapter’s power cord is not connected to the outlet.

2) Connect the RS-232C cable to the connector on the RS-232C interface board, and tighten the left and right screws.

3-2-2. Parallel Cable

To connect a parallel cable, follow the procedure given below.

1) Make sure that the AC adapter’s power cord is not connected to the outlet.

2) Connect the parallel cable to the connector on the parallel interface board, and fasten the connector clasps.

RS-232C cable

Parallel cable

«
...
8
9
10
11
12
...
»

Summary of Contents for TSP043E Series

























Reviews:

No comments

Related manuals for TSP043E Series

Brand: MAKERGEAR Pages: 8

SCX 4500W - Personal Wireless Laser Multi-Function...

Brand: Samsung Pages: 113

imageRUNNER ADVANCE 8105

Brand: Canon Pages: 5

imageCLASS MF269dw

Brand: Canon Pages: 32

Brand: Samsung Pages: 158

imageRUNNER ADVANCE DX C478iZ

Brand: Canon Pages: 208

imageRUNNER ADVANCE DX C477iFZ

Brand: Canon Pages: 92

Brand: Roland Pages: 36

WorkCentre Pro 32

Brand: Xerox Pages: 14

Brand: Lexmark Pages: 807

ID MAKER Zenius

Brand: IDVille Pages: 66

Brand: Olivetti Pages: 315

1235/DX - Phaser Color Laser Printer

Brand: Xerox Pages: 144

Brand: DURACARD Pages: 31

Brand: Kyocera Pages: 44

Brand: Sam4s Pages: 24

Brand: Minolta Pages: 255

Brand: Epilog Laser Pages: 92

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands