Star Micronics LS-5 SERIES Technical Manual Download Page 40

Page: 40 / 204

REPLACEMENT AND ADJUSTMENTS OF PARTS

– 36 –

3-9. Inlet Chute Assembly

(1)

Open the front cover assembly

[1]

(2)

Remove the following units:

•

Inlet chute assembly

[2]

•

Connector (P/J120)

[3]

•

Screw

[4]

Pressing down on the pick up roll assembly

[5]

remove the inlet chute assembly

[2]

, being careful

not to touch the BTR surface of the BTR assembly

[6]

Caution when assembling:
Line up the positioning boss

[7]

of the pick up roll assembly

[5]

with the positioning groove

[8]

of the inlet chute

assembly

[2]

, and attach the inlet chute assembly

[2]

Make sure the inlet chute assembly

[2]

is positioned in front

of the inlet spring, and, being careful not to let the mylar of
the lower chute assembly get caught between the other
parts, attach the inlet chute assembly

[2]

so that the mylar

is positioned upwards of the inlet chute assembly

[2]

when

the front cover assembly

[1]

is open.

3-10. Regi. Sensor

(1)

Open the front cover assembly.

(2)

Remove the following units:

•

Inlet chute assembly

[1]

(according to the proce-

dure described in section 3-9)

•

Regi. sensor

[2]

Summary of Contents for LS-5 SERIES













































































































































































































Search results

Summary of Contents for LS-5 SERIES

Reviews:

Related manuals for LS-5 SERIES

Brands by name

Popular brands

Star Micronics LS-5 SERIES, Technical Manual

Search results

Summary of Contents for LS-5 SERIES

Reviews:

Related manuals for LS-5 SERIES

Brands by name

Popular brands