Star micowave SM Cirius SHC User Manual Download Page 4

Page: 4 / 59

Star Microwave Cirius SHC , 2016

3.4.1.5.1

ADD NEW VLAN ENTRY

............................................................................................... 30

3.4.1.5.2

DELETE VLAN ENTRY

................................................................................................. 30

3.4.2

MRU

......................................................................................................................... 31

3.4.2.1

SYSTEM

INFORMATION

............................................................................................. 31

3.4.2.1.1

CHANGE SYSTEM MODE

............................................................................................. 31

3.4.2.1.2

CHANGE SYSTEM TIME

............................................................................................... 31

3.4.2.2

SYSTEM

.............................................................................................................. 32

3.4.2.3

MODEM

.................................................................................................................... 32

3.4.2.3.1

SELECT BANDWIDTH AND MODULATION

....................................................................... 33

3.4.2.3.2

ACM CONFIGURATION

................................................................................................ 33

3.4.2.4

ODU ....................................................................................................................... 33

3.4.2.4.1

MUTE THE RADIO

....................................................................................................... 34

3.4.2.4.2

TX POWER CONFIGURATION

....................................................................................... 34

3.4.2.4.3

FREQUENCY CONFIGURATION

.................................................................................... 34

3.4.3

SRU

......................................................................................................................... 35

3.4.3.1

MODEM

.................................................................................................................... 35

3.4.3.2

ODU ....................................................................................................................... 35

3.4.4

MSU

......................................................................................................................... 37

3.4.4.1

CHANNEL SWITCH

..................................................................................................... 37

3.4.4.1.1

CONFIGURATION

.................................................................................................. 37

3.4.4.1.2

STM-1

CONFIGURATION

............................................................................................ 37

3.5

MONITOR

.................................................................................................................. 38

3.5.1

SWITCH

.................................................................................................................... 38

3.5.1.1

PORT

STATUS

.......................................................................................................... 38

3.5.1.2

TRAFFIC OVERVIEW

................................................................................................... 38

3.5.1.3

QOS STATISTICS

........................................................................................................ 39

3.5.1.4

DETAILED STATISTICS

................................................................................................ 40

3.5.1.5

MAC TABLE

............................................................................................................... 41

3.5.1.6

VLAN MEMBERSHIP

................................................................................................... 41

3.5.2

MRU

......................................................................................................................... 42

3.5.2.1

SYSTEM

INFORMATION

............................................................................................. 42

3.5.2.2

SYSTEM

SYSTEM LOG

.............................................................................................. 42

3.5.2.3

SYSTEM

RSL LOG

..................................................................................................... 43

3.5.2.4

TEMPERATURE

.......................................................................................................... 43

3.5.2.5

MODEM

.................................................................................................................... 44

3.5.2.6

............................................................................................................................. 44

3.5.2.7

ODU ....................................................................................................................... 44

3.5.2.8

ALARM

..................................................................................................................... 45

3.5.3

SRU

......................................................................................................................... 46

3.5.3.1

SYSTEM

RSL LOG

.................................................................................................... 46

3.5.3.2

MODEM

.................................................................................................................... 46

3.5.3.3

............................................................................................................................. 46

3.5.3.4

ODU ....................................................................................................................... 47

3.5.3.5

ALARM

..................................................................................................................... 47

3.5.4

MSU

......................................................................................................................... 48

3.6

SECURITY WINDOW

................................................................................................... 49

Summary of Contents for SM Cirius SHC




























































Search results

Summary of Contents for SM Cirius SHC

Reviews:

Related manuals for SM Cirius SHC

Brands by name

Popular brands

Star micowave SM Cirius SHC, User Manual

Search results

Summary of Contents for SM Cirius SHC

Reviews:

Related manuals for SM Cirius SHC

Brands by name

Popular brands