8
9
Warning!
Do not use the pressure washer in areas where
there is a risk of explosion or fire from combustible materials.
The sparks possibly caused when using this pressure washer
may ignite combustible materials as well as flammable liquids,
paint, varnish, petrol, flammable gases and dust of an explosive
nature. As a precaution it is recommended that you consult an
expert on a suitable fire extinguisher and its use. Ensure that the
work area is kept clear of combustible materials.
Warning!
Do not use the pressure washer indoors or in
confined spaces.
• Fully assemble pressure washer before use.
• Ensure the pressure cleaner is ‘OFF’ before plugging into the
mains power supply.
• Always use the pressure washer in an open well
ventilated area.
• Unit will become hot during use. Please keep pressure
washer at least one metre (1m) away from buildings, other
equipment, pedestrian areas or flammable materials.
• Ensure the pressure washer has stopped before servicing,
or changing accessories.
• Do not attempt to modify the pressure washer, guards or the
supplied accessories in any way.
• Never operate or store the pressure washer on its side,
ALWAYS operate or store in an upright manner on firm,
solid ground.
• Ensure that the pressure washer has stopped and turned
off when not in use, before servicing, lubricating, making
changes and when changing accessories.
• Your pressure washer is factory set, NEVER attempt to
speed it up as this could endanger the user and damage the
pressure washer and/or attached accessories.
• If the pressure washer makes an unfamiliar sound or
vibrates excessively, switch the pressure washer ‘OFF’
immediately. Investigate the possible cause or consult your
authorised service agent.
• Never use coolant in the pressure washer as damage
may occur.
• Do not tamper or alter any parts as this may cause personal
injury or damage the pressure washer.
• Never point gun/lance at people or animals.
• Never hose or wet people or animals.
• Never spray the pressure cleaner.
• Never spray electrical connections, electrical outlets or
electrical appliances/fixtures.
• Never operate the pressure cleaner without water, any
damage caused will not be covered by warranty.
• Never use hot water.
• Maximum water temperature is 35ºC.
• Only use cold water with this pressure cleaner.
• Bystanders or people watching must be at least 10m away
from operating the pressure cleaner.
• Only use clean water with this pressure cleaner.
• Never pump acids, alkaline, solvents or flammable liquids
through this pressure cleaner, any damage caused will not
be covered under warranty.
• Inlet water hose size must be at least 12mm diameter.
• Inlet flow rate must be at least 18 L/min and mains pressure.
• Damage may occur if pressure washer nozzle is held too
close to the cleaning surface. Damage caused will not be
covered under warranty.
• Always trial the pressure washer cleaner and
selected nozzle on an inconspicuous part of the product
to be cleaned.
• Ensure that the pressure cleaner is disconnected from
the mains supply when not in use, before making
changes or cleaning.
• Always carry your pressure cleaner by its handle.
• Only use Bio-Degradable detergent, with a PH level 6 – 8.
• NEVER use hot, dirty or chemically infested water as it will
damage your pressure cleaner. Only use cold clean water
• Do not start the pressure cleaner with the water trigger ‘ON’.
• Never use a pressure cleaner when standing on a ladder. If
additional height is required a stable platform or approved
scaffold must be used.
• Never clamp your pressure cleaner to a bench or other
device, IT IS A HAND HELD TOOL.
ELECTRICAL DATA
IMPORTANT
This pressure washer is fitted with a sealed electrical connection plug that is compatible with the mains power supply for
Australia / New Zealand and meets the requirements of Australian Standards. This air compressor must be connected to a
supply voltage that is equal to that stated on the rating label. If the mains power connection plug or power cord becomes
damaged you must stop using the pressure washer immediately and it must be replaced with a complete assembly that is
identical to the original, and this must be replaced by an authorised service centre. Always follow the Australian / New Zealand
requirements for connection to the mains supply. If in doubt always consult a qualified electrician.
SPECIFIC SAFETY INSTRUCTIONS
