background image

7

ENGLISH

NOTE: 

Unit may be converted to a 3-wire twist lock cord set 

at an authorized service center.

ACCESSORIES

The performance of any power tool is dependent upon the 
accessory used. Stanley accessories areengineered to high 
quality standards and are designed to enhance the 
performance of power tool.  

Note:

 Accessory must be rated for use at speed equal to or 

higher than nameplate RPM of tool with which it is being 
used.
    

   CAUTION

: The use of any other accessory not 

recommended for use with this tool could be hazardous.Use 
only high-strength Type 1 organic bonded wheels rated 
4100 rpm or higher. Recommended accessories for use with 
your tool are available at extra cost from your local dealer or 
authorized service center.

Protecting The Environment

Should you find one day that your tool needs 
replacement, or if it is of no further use to you, think of 
theprotection of the environment.  Stanley recommends 
you to contact your local council for disposal 
information.

Service Information

Stanley offers a full network of company-owned and 
authorized service locations throughout Asia.  All Stanley 
Service Centers are staffed with trained personnel to 
provide customers with efficient and reliable power tool 
service.Whether you need technical advice, repair, or 
genuine factory replacement parts, contact the Stanley 
location nearest to you.

Notes

Stanley's policy is one of continuous improvement to 
our products and, as such, we reserve the right 
tochange product specifications without prior notice.
Standard equipment and accessories may vary by 
country.
Product specifications may differ by country.
Complete product range may not be available in all 
countries.  
Contact your local Stanley dealers for range availability.

MAINTENANCE

Your Stanley power tool has been designed to operate over 
a long period of time with a minimum of 
maintenance.Continuous satisfactory operation depends 
upon proper tool care and regular cleaning.Your tool is not 
user-serviceable.  Take the tool to an authorized Black & 
Decker repair agent.  This tool should be serviced at 
regular intervals or when showing a noticeable change in 
performance.

Lubrication

Stanley power tools are properly lubricated at the factory 
and are ready for use.  Tools should be re-lubricated 
regularly , depending on usage.  This lubrication should 
only be attempted by trained power tool repair persons, 
such as those at Stanley service centers or by other 
qualified service personnel.
Closed-type, grease-sealed ball bearings are used 
throughout. These bearings have sufficient lubrication-
packed in them at the factory to last the life of the chop 
saw.

Cleaning

       Warning:

 unplug the tool before you use a cloth to 

clean the housing.With the motor running, blow dirt and 
dust out of all air vents with dry air at least once a week.  
Wear safety glasses when performing this.  Exterior plastic 
parts may be cleaned with a damp cloth and mild 
detergent.  Although these parts are highly solvent 
resistant, NEVER use solvents.

Blowing dust and grit out of the main housing by means of 
an air hose is recommended and may be done as often as 
dirt is seen collecting in and around the air vents. Always 
wear proper eye and respiratory protection.

Tool Care

Avoid overloading the machine.Overloading will result in a 
considerable reduction in speed and efficiency and the unit 
will become hot.  In this event,run the machine at no load 
for a minute or two until cooled to normal working 
temperature by the built in fan.  Switching your machine on 
and off whilst under load will considerably reduce the life of 
the switch.

Important

To ensure product SAFETY and RELIABILITY, repairs, 
maintenance and adjustment (other than those listed in this 
manual) should be performed by authorized service centers 
or other qualified organizations, always-using identical 
replacement parts.  Unit contains no user serviceable parts 
inside.Blowing dust and grit out of the main housing by 
means of an air hose is recommended and may be done as 
often as dirt is seen collecting in and around the air vents. 
Always wear proper eye and respiratory protection.


Summary of Contents for STEL705

















Reviews: