10
ENGLISH (
Original Instructions)
or other blind areas.
The protruding blade may cut
objects that can cause kickback.
Lower guard safety instructions
a. Check the lower guard for proper closing before
each use.
Do not operate the saw if lower guard
does not move freely and close instantly. Never
clamp or tie the lower guard into the open position.
If saw is accidentally dropped, lower guard may be bent.
Raise the lower guard with the retracting handle and
make sure it moves freely and does not touch the blade
or any other part, in all angles and depths of cut.
b. Check the operation of the lower guard spring.
If
the guard and the spring are not operating properly,
they must be serviced before use.
Lower guard may
operate sluggishly due to damaged parts, gummy
deposits, or a build-up of debris.
c. The lower guard should be retracted manually
only for special cuts such as “plunge cuts” and
“compound cuts”.
Raise lower guard by retracting
handle and as soon as blade enters the material, the
lower guard must be released.
For all other sawing,
the lower guard should operate automatically.
d. Always observe that the lower guard is covering
the blade before placing saw down on bench or
floor.
An unprotected, coasting blade will cause the
saw to walk backwards, cutting whatever is in its path.
Be aware of the time it takes for the blade to stop after
switch is released.
ADDITIONAL SAFETY INSTRUCTIONS FOR
CIRCULAR SAWS
•
Wear ear protectors.
Exposure to noise can cause
hearing loss.
•
Wear a dust mask.
Exposure to dust particles can
cause breathing difficulty and possible injury.
•
Do not use blades of larger or smaller diameter than
recommended.
For the proper blade rating refer to the
technical data. Use only the blades specified in this
manual, complying with EN 847-1.
•
Never use abrasive cut-off and diamond wheels.
Do
not cut concrete, brick, steel or other hand materials.
•
Do not use water feed attachments.
•
Use clamps or another practical way to secure and
support the workpiece to a stable platform.
Holding
the work by hand or against your body leaves it unstable
and may lead to loss of control.
•
Do not use this saw as a table saw.
Additional safety information
WARNING
: We recommend the use of a residual
current device with a residual current rating of
30mA or less.
SAFETY OF OTHERS
• This tool is not intended for use by persons (including
children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge,
unless they have been given supervision or instruction
concerning use of the tool by a person responsible for
their safety.
• Children should be supervised to ensure that they do
not play with the appliance.
RESIDUAL RISKS
In spite of the application of the relevant safety regulations
and the implementation of safety devices, certain residual
risks cannot be avoided. These are:
– Impairment of hearing
– Risk of personal injury due flying particles.
– Risk of burns due to accessories becoming hot
during operation.
– Risk of personal injury due to prolonged use.
– Risk of dust from hazardous substances.
ELECTRICAL SAFETY
Your tool is double insulated; therefore no earth
wire is required. Always check that the main
voltage corresponds to the voltage on the rating
plate.
WARNING
! If the power cord is damaged, it must
be replaced by the manufacturer, authorized
STANLEY Service Center or an equally qualified
person in order to avoid damage or injury. If the
power cord is replaced by an equally qualified
person, but not authorized by STANLEY, the
warranty will not be valid.
USING AN EXTENSION CABLE
If an extension cable is required, use an approved 3–core
extension cable suitable for the power input of this tool (see
Technical Data).The minimum conductor size is 1.5 mm2;
the maximum length is 30 m. When using a cable reel,
always unwind the cable completely.
Cable cross-sectional
area (mm
2
) Cable rated
current (Ampere)
Cable cross-sectional
area (mm
2
) Cable rated
current (Ampere)
0.75
6
1.00
10
1.50
15
2.50
20
4.00
25
Summary of Contents for SC12
