4. Replace center pin and spring inside plug.
5. Replace gold cap by turning clockwise.
ACCESSORIES
Recommended accessories for use with your tool are available from your local dealer or authorized service center. If
you need assistance regarding accessories, please contact manufacturer at (877) 571-2391.
WARNING:
The use of any accessory not recommended for use with this appliance could be hazardous.
SERVICE INFORMATION
Whether you need technical advice, repair, or genuine factory replacement parts, contact the manufacturer at
(877) 571-2391.
FIVE-YEAR LIMITED WARRANTY
Manufacturer warrants this product for five years against any defects in material or workmanship. The defective
product will be replaced or repaired at no charge in either of two ways.
The first, which will result in exchanges only, is to return the product to the retailer from whom it was purchased
(provided that the store is a participating retailer). Returns should be made within the time period of the retailer’s
policy for exchanges (usually 30 to 90 days after the sale). Proof of purchase may be required. Please check with
the retailer for their specific return policy regarding returns that are beyond the time set for exchanges. The second
option is to return the product (prepaid) to the manufacturer for repair or replacement at our option. Proof of
purchase may be required.
This warranty does not apply to accessories. This warranty gives you specific legal rights and you may have other
rights which vary from state to state or province to province. This product is not intended for commercial use.
SPECIFICATIONS
Input :
120 volts AC, 60Hz, 0.6A
Output:
6 volts DC, 2A
12 volts DC, 2A
Imported by
Baccus Global
399 NW 2nd Avenue, Suite 150,
Boca Raton, FL 33432
(877) 571-2391
RD111709
9
Note:
If the clamps are incorrectly connected with regard to polarity, the reverse polarity LED (
) will light. Unplug the
charger; then remove the clamps. Reconnect the clamps properly.
7. When the unit is properly connected and charging, the battery charging LED
(
)
will light to indicate the
battery is charging.
8. When the charging complete LED (
) lights, the battery is fully charged.
When disconnecting charger, disconnect AC cord, remove clamp from vehicle chassis, and then remove clamp from
battery terminal.
Charging Using the 12 Volt DC Charging Adapter
1. Set the battery voltage selector to the correct voltage.
2. Insert the double barrel tip of the 12 volt DC charging adapter cable into the battery charger; then plug the
battery charger’s power cord into an AC outlet. The power LED will light red to indicate that the charger is
plugged in and ready.
3. Insert the gold-tipped 12 volt DC charging adapter plug into the vehicle’s 12 volt DC accessory outlet. Rotate
the adapter slightly to make sure there is good contact.
4. When the unit is properly connected and charging, the battery charging LED
(
)
will light to indicate the
battery is charging.
5. When the charging complete LED (
) lights, the battery is fully charged.
When disconnecting charger, disconnect AC cord, and then remove the 12 volt DC charging adapter from the
vehicle accessory outlet.
TROUBLESHOOTING
Unit Not Charging
• Check that the charger is properly connected to a live 120 volt AC outlet (the power LED will illuminate).
• Check that the correct charge rate has been selected for the battery being charged.
• If the battery to be charged has fallen below 2 volts, the battery cannot be recharged with this unit.
CARE AND MAINTENANCE
Storage
• Store the unit in a clean, dry, cool place when not in use.
• Clean the unit casing and cords (as necessary) with a dry (or slightly damp) cloth. Ensure that unit is completely
disconnected from battery and power source before cleaning.
• To maintain the operating condition and maximize the life of the charger cords, always coil them loosely for
storage. Do not wrap them around the unit or crimp them with a tight band.
Fuse Replacement (12 Volt DC Charging Adapter)
1. Remove plug from accessory outlet. Remove the gold cap by turning counterclockwise and lifting off.
2. Remove center pin and spring. Remove fuse.
3. Replace fuse with same type and size fuse (5 amp).
8
BC209_ManualENSP_111709.qxp 11/17/2009 3:51 PM Page 8
