Stanley 2-Way Feed Chipper / Shredder Owner'S Manual Download Page 2

 

2 of 12 

 

STANLEY is a registered trademark of The Stanley Works or its affiliates and are used under license by GXi Outdoor Power LLC. 

Rev

. 9/2010 

WARNINGS 

Training 

1. 

Read, understand, and follow all instructions on the machine and in the 
manual(s) before attempting to assemble and operate. Keep this manual 
in a safe place for future and regular reference and for ordering replace-
ment parts.  

2. 

Be familiar with all controls and their proper operation. Know how to 
stop the machine and disengage them quickly.  

3. 

Never allow children under 16 years old to operate this machine. Chil-
dren 16 years old and over should read and understand the operation 
instructions and safety rules in this manual and should be trained and 
supervised by a parent.  

4. 

Never allow adults to operate this machine without proper instruction.  

5. 

Keep bystanders, helpers, pets, and children at least 75 feet from the 
machine while it is in operation. Stop machine if anyone enters the area.  

6. 

Never run an engine indoors or in a poorly ventilated area. Engine ex-
haust contains carbon monoxide, an odorless and deadly gas.  

7. 

Do not put hands and feet near rotating parts or in the feeding chambers 
and discharge opening. Contact with the rotating impeller can amputate 
fingers, hands, and feet.  
 
 

DANGER: 

This machine was built to be operated according to the rules for 

safe operation in this manual. As with any type of power equipment, careless-
ness or error on the part of the operator can result in serious injury. This ma-
chine is capable of amputating hands and feet and throwing objects. Failure 
to observe the following safety instructions could result in serious injury or 
death. 

WARNING:

 The Engine Exhaust from this product contains chemicals known 

to the State of California to cause cancer, birth defects or other reproductive 
harm. 

WARNING:

 This symbol points out important safety instructions which, if not 

followed, could endanger the personal safety and/or property of yourself and 
others. Read and follow all instructions in this manual before attempting to 
operate this machine. Failure to comply with these instructions may result in 
personal injury. When you see this symbol - heed its warning.  

8. 

Never attempt to unclog either the feed intake or discharge opening, 
remove or empty bag, or inspect and repair the machine while the en-
gine is running. Shut the engine off and wait until all moving parts have 
come to a complete stop. Disconnect the spark plug wire and ground it 
against the engine. 

This owner’s manual is considered a permanent part of the chipper shredder 
and should remain with the chipper shredder if resold. The information and 
specifications included in this publication were in effect at the time of ap-
proval for printing. 
 
GXi Outdoor Power LLC, exclusive marketer of STANLEY Heavy Duty Power 
Equipment, reserves the right to discontinue or change specifications or de-
sign at any time without notice and without incurring any obligation what so 
ever. No part of this publication may be reproduced without written permis-

WARNING 

WARNING 

WARNINGS 

 

WARNING 

WARNING:  Do not operate this machine unless the chute deflector 

has been installed properly. 

WARNING 

WARNING:  Rotating cutting blades.  Keep hands and feet out of 

WARNING 

WARNING

:  Do not deposit branches larger than 4 inch  

diameter in the chute.  Do not deposit branches larger than 1/4 inches into the 

funnel. 

 

WARNING 

WARNING

:  

Safety glasses should be worn while  

operating this machine or if you are standing within 75 ft. of the machine.

 

WARNING

:  Keep bystanders, helpers, pets, and children at least 75 feet 

from the machine while it is in operation. Stop machine if anyone enters the 

area.  

WARNING 

Never wear loose clothes or long jewelry and keep your long hair under a 

headgear when operating machine.  

Never use machine on a slope or hard smooth floor.  

Summary of Contents for 2-Way Feed Chipper / Shredder













Reviews: