1
Standard Pump Operating Instructions and Parts Manual (
OIPM-IND-0713
)
Standard Pump
Industrial Drum Pump Models:
SP-PP, SP-PHT, SP-CPVC, SP-AL, SP-PVDF & SP-SS
* When operating in Hazardous Duty applications a pump must be used in conjunction with an explosion proof motor or air motor.
Model
Material of
Construction
Maximum Liquid
Temperature
Wetted Materials
Maximum Flow Rate
Discharge
Pressure
SP-CPVC
CPVC
190º F (90º C)
CPVC, Carbon, Hastelloy C, PVDF, PTFE
35 gpm (132 l/min)
16 psi (1,1 bar)
SP-CPVC-HH
CPVC
190º F (90º C)
CPVC, Carbon, Hastelloy C, PVDF, PTFE
16 gpm (60 l/min)
32 psi (2,2 bar)
SP-PP
Polypropylene
130º F (55º C)
PP, Carbon, Hastelloy C, PTFE
35 gpm (132 l/min)
16 psi (1,1 bar)
SP-PP-HH
Polypropylene
130º F (55º C)
PP, Carbon, Hastelloy C, PTFE
16 gpm (60 l/min)
32 psi (2,2 bar)
SP-PHT
Polypropylene
175º F (80º C)
PP, Carbon, Hastelloy C, PTFE
35 gpm (132 l/min)
16 psi (1,1 bar)
SP-PHT-HH
Polypropylene
175º F (80º C)
PP, Carbon, Hastelloy C, PTFE
16 gpm (60 l/min)
32 psi (2,2 bar)
SP-PVDF
PVDF (Kynar
®
)
175º F (80º C)
PVDF, Carbon, Hastelloy C, PTFE
35 gpm (132 l/min)
16 psi (1,1 bar)
SP-PVDF-HH
PVDF (Kynar
®
)
175º F (80º C)
PVDF, Carbon, Hastelloy C, PTFE
16 gpm (60 l/min)
32 psi (2,2 bar)
*SP-SS
SS316
175º F (80º C)
SS316, Carbon, PTFE
35 gpm (132 l/min)
16 psi (1,1 bar)
*SP-SS-HH
SS316
175º F (80º C)
SS316, Carbon, PTFE
16 gpm (60 l/min)
32 psi (2,2 bar)
*SP-AL
Aluminum
175º F (80º C)
Aluminum, Carbon, PTFE & SS316
35 gpm (132 l/min)
16 psi (1,1 bar)
*SP-AL-HH
Aluminum
175º F (80º C)
Aluminum, Carbon, PTFE & SS316
16 gpm (60 l/min)
32 psi (2,2 bar)
Drum Pump Specifications
Description
Standard’s Drum Pumps are designed to
transfer a variety of materials from 55 gallon
drums and tanks. Standard Pump offers
several different pumps, each designed
for specific applications. Before operating,
please confirm that the pump’s materials of
construction are suitable for the application.
Unpacking
Cartons should be handled with care to avoid
damage from dropping, etc. After unpacking,
inspect carefully for any damage that may
have occurred during transit. Check for loose,
damaged or missing parts.
General Safety Information
The responsibility for safe assembly,
installation, and operation ultimately rests
with the operator. Read and understand ALL
safety precautions and operating instructions
before operation. Careless pump operation
can result in serious injury.
1.
Before operating the pump, read and
understand these operating instructions.
2.
The operator should wear suitable
protective clothing including the
following: face mask, safety shield or
goggles, gloves, apron, and safety
shoes.
3.
Before operating, verify the materials
being pumped are compatible with the
pump’s “wetted components."
4.
All Federal, State, and local safety codes
should be followed.
5.
Verify that the motor voltage
corresponds to proper electrical supply.
6.
Before plugging motor into power
supply, make sure the motor switch is in
the OFF position. For Air Motors ensure
inlet valve is closed before attaching air
line.
7.
Before operation, confirm all pump
connections are properly tightened.
8.
First pump clean water in order to
familiarize yourself with the pump’s
operation, flow rate, discharge pressure
and motor speed.
9.
Before starting the pump, confirm the
discharge hose is securely fastened to
the receiving vessel in order to prevent
splashing.
10.
Never leave pump unattended during
operation.
11.
Do not submerge the motor in any liquid.
12.
When finished using the pump, flush
the pump by pumping water or an
appropriate cleaning solution. Do not
use flammable or combustible cleaning
solutions.
13.
Never carry the motor by the power
cord.
14.
Never store pump in container. Always
rinse pump thoroughly and hang on wall
bracket or ensure pump tube is stored in
an upright and vertical position.
When pumping
flammable or
combustible products or operating in a
hazardous duty environment, the SP-AL
or SP-SS Series pump must be used in
conjunction with an explosion proof
motor. Please contact the factory or an
authorized distributor with any questions
regarding this matter.
Assembly
1.
Remove the pump and motor from
packaging.
2.
Inspect all contents for damage.
3.
Couple the motor to the pump tube by
using the Hand Wheel. (See figure 1).
Figure 1