background image

3

NOTES

•  The RAM4X is only floating / submersible

*

 when the USB jack is properly sealed with jack cover. 

*(IPX8 Specification for submersibility: 4.92 ft. (1.5 m) for 30 minutes.)

•  Make sure that there is no dust, dirt or crack on the jack or the rubber gasket.

•  Remove any dust and dirt before closing the cover.

•  If you find any cracks on the jack cover or gasket, please contact Standard Horizon or your local 

dealer to purchase a replacement.

•  To keep the LCD, keypad and speaker grill clean and in top operating condition after exposure 

to water: Clean the RAM4X with fresh water after exposure to salt water by rinsing the RAM4X 

under a sink faucet or by dunking the RAM4X in a bucket of fresh water. After washing, use a 

soft cloth and thoroughly dry all parts of the RAM4X.

Included Accessories and replacement part numbers

• 

SAD-17

  USB Wall Charger  (100-240 VAC)

• 

T9101648

  USB Cable  (Type USB “A” plug to Type USB micro “B” plug)

• 

CLIP-22

  Belt Clip

• 

SCH-11

  Belt Clip Hanger & Screws  (U40412220 x 2 pcs)

•  Hand Strap

Optional Accessories

• 

SCU-30

  Wireless Access Point with 5 feet (1.5 m) Cable*

  *(The SCU-30 firmware must be Ver. 2.00.00 or later.)

• 

SDD-14

  USB DC Charger with Cigarette Lighter Plug

Belt Clip Installation / Removal

1.  To install the Belt Clip 

CLIP-22,

 align it to the groove of 

the rear panel, then press the Belt Clip downward until it 

locks in place with a “Click”.

2.  To remove, pull the 

CLIP-22

 latch tab away from the rear 

panel to unlock the 

CLIP-22

, then slide the 

CLIP-22

 upward 

to remove it.

Battery Charging

If  the  battery  has  never  been  used,  or  its 

charge  is  depleted,  charge  the 

RAM4X

 ac

-

cording to the following procedures:

1. 

Turn the 

RAM4X

 OFF.

2.  Slide the USB jack cover button down to 

open the cover.

3.  Referring to the figure at the right, connect 

the supplied USB Cable to the USB jack.

SAD-17

USB Cable

(Supplied)

4. 

If the connection is correct, the 

RAM4X

’s LCD display will show the battery 

charging icon.

5.  A fully discharged 

RAM4X

 will be charged completely in approximately 4 hours.

When charging is completed, the battery charging icon will disappear.

Summary of Contents for RAM4X

















Reviews: