background image

IMPORTANT

 

:  Before filling out the form below make sure you have the right information.

Refer to the parts list to make sure you're ordering the right parts!

Detach and Mail or Fax the Form Below

Stamina Products, Inc.

P.O. Box 1071

Springfield, MO 65801-1071

IMPORTANT

 

:  We must have your phone number in order to process the order!

FAX/MAIL ORDERING FORM

Please do not return the product.  For your convenience, Stamina has a Customer Service Department with
a toll-free number.  Should a part be missing or a defective part found, please call 

1 (800) 375-7520

(in the U.S.) between 8:00 A.M. and 5:00 P.M. Central Time, Monday through Friday or fill out the fax sheet
ordering form below and fax it to 

(417) 889-8064.

  Our Customer Service Department will be able to assist

you with your problem and the part will be mailed directly to your house.

TELEPHONE

CUSTOMER SERVICE

Tel: 1 (800) 375-7520

FAX

CUSTOMER SERVICE

Fax: (417) 889-8064

MAIL

STAMINA PRODUCTS, INC.

ATTN: Customer Service

P.O. Box 1071

Springfield, MO. 65801-1071

ONLINE

CUSTOMER SERVICE

[email protected]

www.staminaproducts.com

Mr./Ms:

Address:

     Apt. #:

City:

State:

     Zip Code:

Phone #: (        )

          Work Phone #: (        )

Date Purchased:

Model #:

Purchased From:

    

PART #

          DESCRIPTION

                 QUANTITY

         

1

      Rear Unit Assembly

  1

EXAMPLE:

Summary of Contents for 55-1538



















Reviews: