07
07.1 RESET USING THE BUTTONS ON THE SENSOR
07. RESET
A
B
C
This procedure restores the factory settings of the device. Moreover, it deletes the transmitter for sensor control, if memorized.
This procedure must be carried out by qualified technical personnel.
With this procedure the sensor IS NOT DELETED FROM THE MEMORY OF THE TUNED RECEIVERS.
Press at the same time
P1
and
P3.
Hold the buttons. After a few seconds the
three LEDs start flashing.
Hold
P1
and
P3
for around 30 sec, the three LEDs light on.
Release the buttons: the three LEDs light off.
RESET COMPLETED!!
P1
P3
P1
P3
P1
P3
ü
The device is in “Wind alarm”.
ü
Sun threshold is too high. Adjust the threshold.
ü
The device could be installed in a position little exposed to the sun, or some object obstructs the proper detection of the sun.
ü
Sun function is deactive.
ü
The sun sensor may be damaged. Check functionality by checking that "sun LED" blinks quickly once you apply a light source at the oval on the
device.
ü
Radio connection could be disturbed. The Test Radio function is active. If the receiver doesn't receive any information from radio sensor over the
defined time, the receiver commands an upward movement to protect the awning.
ü
Radio sensor or receiver device doesn't work. The Radio Test function is active. If all receiver devices associated to the sensor are in this condition,
probably the sensor is failure. If only one receiver device is in this condition, probably this last one is failure.
ü
Wind threshold is to high. Adjust the threshold.
ü
The device could be installed in a position little exposed to the wind.
ü
The wind sensor may be damaged. Check the functioning by turning the cups to simulate the presence of the wind and make sure that device enter in
"wind alarm”.
ü
Interferences on Radio connection. Verify that there are no interferences on same frequency.
08. FAQ
ü
Verify the power supply.
ü
Once powered, the device lights LEDs briefly to indicate the proper power supply. If this doesn't happen, it is likely a fault and it may be necessary to replace
the device or there is an error in the electrical connection.
ü
Ensuring to have correctly operated the storage process of remote control of sensor controlling.
ü
The procedure of memorization of remote control has been made too slowly. When device entries into “transmitter programming” mode, you have 15
sec to press the STOP button of the transmitter you want to store.
ü
You have set up a threshold out of sensor limits.
THE DEVICE DOESN'T WORK
IN PRESENCE OF WIND, THE UPWARD MOVEMENT IS COMMANDED BUT IN PRESENCE OF SUN THE DOWNWARD MOVEMENT IS NOT
COMMANDED
WITHOUT WIND THE MOTORS MAKE AN UPWARD MOVEMENT
IN PRESENCE OF WIND, THE UPWARD MOVEMENT IS NOT COMMANDED
THE SENSOR COMMANDS MOTORS CORRECTLY BUT, WHEN I TRY TO CHANGE SUN / WIND THRESHOLD BY THE REMOTE CONTROL FOR
SENSOR CONTROLLING, THERE ARE NO SIGNALS BY MOTORS
WHEN I TRY TO CHANGE SUN / WIND THRESHOLD FROM REMOTE CONTROL, MOTORS MAKE 2 SMALL DOWNWARD MOVEMENTS
ü
The sensor is able to memorize only one remote control. Sensor considers only the last one memorized.
WHEN I TRY TO STORE A SECOND REMOTE CONTROL FOR SENSOR, THE FIRST REMOTE CONTROL DOESN'T MODIFY THRESHOLDS
All rights reserved.
STAFER S.p.a. - via Malpighi, 9 - 48018 Faenza (RA) ITALY
Tel. (+39) 0546.624811 - Fax. (+39) 0546.623141 - www.stafer.com
All products and technical specifications given in this document are subject to variation without notice. Unless previously and specifically authorised by STAFER, the device must be
used exclusively with transmitters produced by STAFER.
STAFER cannot be consider responsible for damage caused by improper, incorrect or unreasonable uses.
