Stac THERMAFLOW SS980H Resource Manual Download Page 19

The THERMAFLOW SS980 Series Hydraulic Cooler is warranted against any 

defect in material and workmanship which existed at the time of sale, by STAC Inc. 

according to the following provisions, subject to the requirements that the Cooler 

must be used only in accordance with the catalogue and package instructions.

The cooler is warranted for a period of TWO Years from the date of installation. If 

during the warranty period the cooler fails to operate to STAC’s specifications due 

to a defect in any part in material or workmanship that existed at the time of sale by 

STAC Inc., the defective part will be repaired or replaced, at STAC Inc.’s discretion, 

at no charge, if the defective part is returned to STAC Inc. with transportation 

prepaid.

The above warranty shall terminate if any alterations or repairs are made to the 

System other than at an authorized dealer or if the cooler is used on any equipment 

other than the equipment upon which it is first installed.

THE FORGOING WARRANTIES ARE IN LIEU OF ALL OTHER OBLIGATIONS 

AND LIABILITIES, INCLUDING NEGLIGENCE AND ALL WARRANTIES OF 

MERCHANTABILITY AND SUITABILITY, EXPRESSED OR IMPLIED AND STATE 

STAC INC.’S ENTIRE AND EXCLUSIVE LIABILITY AND BUYER’S EXCLUSIVE 

REMEDY FOR ANY CLAIM OF DAMAGES IN CONNECTION WITH THE SALE, 

REPAIR OR REPLACEMENT OF THE ABOVE GOODS, THEIR DESIGN, 

INSTALLATION OR OPERATION.  STAC INC. WILL IN NO EVENT BE LIABLE 

FOR ANY DIRECT, INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL 

DAMAGES WHATSOEVER, AND OUR LIABILITY UNDER NO CIRCUMSTANCES 

WILL EXCEED THE CONTRACT PRICE FOR THE GOODS FOR WHICH 

LIABILITY IS CLAIMED.

60 West Sycamore Street • St. Paul, MN  55117

800-334-7699 • 763-235-7822 Fax

Web: www.thermaflow.com

Inc.

THERMAFLOW WARRANTY

Thermaflow is a registered trademark of STAC, Inc.  All Rights Reserved. 

 

Form 980901  Rev: 10/19

Mobile Hydraulic Systems

®

Summary of Contents for THERMAFLOW SS980H




















Reviews: