manualshive.com logo in svg

ST SPSGRF, Datasheet, Page: 16 / 25

Share
Download
ST SPSGRF Datasheet Download Page 16

Regulatory compliance

SPSGRF

16/24

DocID027664 Rev 6

Modifications or changes to this equipment not expressly approved by STMicroelectronics 
may render void the user's authority to operate this equipment.

Modular approval

IC: 8976C-SPSGRF

In accordance with IC RSS-210, the SPSGRF-915 is listed as a modular transmitter device.

This module is evaluated for stand-alone use only. Finished products incorporating multiple 
transmitters must comply with collocation and RF exposure requirements in accordance 
with IC multi-transmitter product procedures. Collocated transmitters operating in portable 
RF exposure conditions (e.g. <20 cm from persons including but not limited to body worn 
and hand-held devices) may require separate approval.

6.2.1 Labeling 

instructions

When integrating the SPSGRF-915 into the final product, the OEM must ensure that the IC 
labeling requirements are satisfied. A statement must be included on the exterior of the final 
product which indicates that the product includes a certified module. The label should state 
the following (or similar wording that conveys the same meaning):

          

          

The OEM must include the following statements on the exterior of the final product unless 
the product is too small (e.g. less than 4 x 4 inches):

“This device complies with RSS-210 of the IC Rules. Operation is subject to the following 
two conditions:
1.

this device may not cause harmful interference

2.  this device must accept any interference received, including any interference that may 

cause undesired operation.”

6.2.2 

Product manual instructions

This section applies to OEM final products containing the SPSGRF-915 module, subject to 
IC compliance. The final product manual must contain the following statement (or a similar 
statement that conveys the same meaning):

“Warning: Changes or modifications not expressly approved by the party responsible for 
compliance could void the user's authority to operate the equipment. (RSS-210)”

In the case where an OEM seeks Class B (residential) limits for the final product, the 
following statement must be included in the final product manual:

“Note: This equipment has been tested and found to comply with the limits for a Class B 
digital device, pursuant to RSS-210 of the IC Rules. These limits are designed to provide 
reasonable protection against harmful interference in a residential installation. This 
equipment generates, uses and can radiate radio frequency energy and, if not installed and 
used in accordance with the instructions, may cause harmful interference to radio 
communications. However, there is no guarantee that interference will not occur in a 
particular installation. If this equipment does cause harmful interference to radio or 

Contains IC ID: 8976C-SPSGRF

OR

This product contains IC ID: 8976C-SPSGRF

Summary of Contents for SPSGRF


























Reviews:

No comments