manualshive.com logo in svg

ST SPSGRF, Datasheet, Page: 14 / 25

Share
Download
ST SPSGRF Datasheet Download Page 14

Regulatory compliance

SPSGRF

14/24

DocID027664 Rev 6

6 Regulatory 

compliance

6.1 FCC 

certification

The SPSGRF-915 module has been tested and found compliant with the FCC part 15 rules. 
These limits are designed to provide reasonable protection against harmful interference in 
approved installations. This equipment generates, uses, and can radiate radio frequency 
energy and, if not installed and used in accordance with the instructions, may cause harmful 
interference to radio communications.

However, there is no guarantee that interference may not occur in a particular installation.

This device complies with part 15 of the FCC rules. Operation is subject to the following two 
conditions: (1) this device may not cause harmful interference, and (2) this device must 
accept any interference received, including interference that may cause undesired 
operation.

Modifications or changes to this equipment not expressly approved by STMicroelectronics 
may render void the user's authority to operate this equipment.

Modular approval

FCC ID: S9NSPSGRF

In accordance with FCC part 15, the SPSGRF-915 is listed as a modular transmitter device.

This module is evaluated for stand-alone use only. Finished products incorporating multiple 
transmitters must comply with collocation and RF exposure requirements in accordance 
with FCC multi-transmitter product procedures. Collocated transmitters operating in portable 
RF exposure conditions (e.g. <20 cm from persons including but not limited to body worn 
and hand-held devices) may require separate approval.

6.1.1 Labeling 

instructions

When integrating the SPSGRF-915 into the final product, the OEM must ensure that the 
FCC labeling requirements are satisfied. A statement must be included on the exterior of the 
final product which indicates that the product includes a certified module. The label should 
state the following (or similar wording that conveys the same meaning): 

          

          

The OEM must include the following statements on the exterior of the final product unless 
the product is too small (e.g. less than 4 x 4 inches):

This device complies with part 15 of the FCC rules. Operation is subject to the following two 
conditions: 
1.  this device may not cause harmful interference
2.  this device must accept any interference received, including any interference that may 

cause undesired operation.

Contains FCC ID: S9NSPSGRF 

OR

This product contains FCC ID: S9NSPSGRF 

Summary of Contents for SPSGRF


























Reviews:

No comments