manualshive.com logo in svg

ST SP1ML-915, Preliminary Data Sheet, Page: 16 / 19

Share
Download
ST SP1ML-915 Preliminary Data Sheet Download Page 16

 

16/19 

Doc ID TBD Rev 0.8 

Rev 0.1 

 

www.st.com

 

 

5.3 

Labeling instructions 

When  integrating  the  SP1ML-915  into  the  final  product,  the  OEM  must  ensure  that  the 
FCC labeling requirements are satisfied. A statement must be included on the exterior of 
the final product which indicates the product includes a certified module. The label should 
state the following (or similar wording that conveys the same meaning): 

Contains FCC ID: S9NSP1ML

  

OR

   

This product contains FCC ID: S9NSP1ML

  

The OEM must include the following statements on the exterior of the final product unless 
the product is too small (e.g. less than 4 x 4 inches): 

This  device  complies  with  Part  15  of  the  FCC  Rules.  Operation  is  subject  to  the 
following  two  conditions:  (1)  this  device  may  not  cause  harmful  interference,  and 
(2)  this  device  must  accept  any  interference  received,  including  any  interference 
that may cause undesired operation. 

5.4 

Product manual instructions 

This section applies to OEM final products containing the SP1ML-915 module, subject to 
FCC  compliance.  The  final  product  manual  must  contain  the  following  statement  (or  a 
similar statement that conveys the same meaning): 

WARNING:    Changes  or  modifications  not  expressly  approved  by  the  party 
responsible for compliance could void the user’s authority to operate the equipment 

 

In  the  case  where  an  OEM  seeks  Class  B  (residential)  limits  for  the  final  product,  the 
following statement must be included in the final product manual: 

NOTE:  This  equipment has  been tested  and  found  to  comply  with the  limits for a 
Class  B  digital  device,  pursuant  to  part  15  of  the  FCC  Rules.  These  limits  are 
designed  to  provide  reasonable  protection  against  harmful  interference  in  a 
residential  installation.  This  equipment  generates,  uses  and  can  radiate  radio 
frequency energy and, if not installed and used in accordance with the instructions, 
may  cause  harmful  interference  to  radio  communications.  However,  there  is  no 
guarantee  that  interference  will  not  occur  in  a  particular  installation.  If  this 
equipment does cause harmful interference to radio or television reception, which 
can be determined by turning the equipment off and on, the user is encouraged to 
try to correct the interference by one or more of the following measures: 

 

Reorient or relocate the receiving antenna. 

 

Increase the separation between the equipment and receiver. 

 

Connect the equipment into an outlet on a circuit different from that to which the 

receiver is connected. 

 

Consult the dealer or an experienced radio/TV technician for help. 

 

Summary of Contents for SP1ML-915




















Reviews:

No comments