SSV Works GN-5A Manual Download Page 25

25

Polaris General

 

MRB3 Dash Panel

!

Please read and understand these 

instructions completely before 

installation to avoid possible injury, or 

damage to the accessory or vehicle. 

WARRANTY INFORMATION:

All SSV Works enclosures are covered by a limited lifetime warranty against defects in 

material or workmanship. All SSV Works Electronics are covered by a limited 1 year warranty 

against defects in material or workmanship. All SSV Works Speakers are covered by a 

limited 1 year warranty against defects in material or workmanship. Labor for replacement of 

defective components is not covered. Contact SSV Works for further warranty information.

SSV WORKS, 201 N. Rice Ave Unit A, Oxnard, CA 93030

www.SSVworks.com     |     Phone: 818-991-1778     |     Fax: 866-293-6751

TOOLS NEEDED FOR INSTALLATION

- #2 Phillips Screwdriver

PARTS LIST IMAGES

2.   MRB3 Bluetooth 

Media Player

1.    MRB3 Dash Panel

3.  MRB3 Power & Ground 

Connector

A

B

A. With a #2 Phillips screw driver, secure the MRB3 controller to the 

dash kit with the 2 screws supplied in the MRB3 box.

B. Connect MRB3 controller to the MRB3 Brain and secure cables. 

Summary of Contents for GN-5A





























Reviews: