SSCOR DUET 2314 Series Operating Instructions & Maintenance Manual Download Page 2

1. SSCOR suction units are not designed or intended for use in extended procedures that require prolonged 

 

high vacuum/low airflow applications, as is the case in wound drainage or endoscopic use or in any other 

 

procedure that produces high vacuum levels within an occluded system for an extended period of time. 

 

Turn the suction unit off when it is not in use.

 

 

2. Federal law restricts this device to sale, distribution, and use by, or on the order of a physician, emergency 

 

 

medical technician, or other medical practitioner. For use by medical personnel trained in suctioning 

 

 

techniques and in the use of medical suction equipment.

 

 

3. Operator should be thoroughly familiar with these operating instructions before this device is used.

 

 

4. Do not use in the presence of flammable agents or anesthetics.

 

 

5. Before testing for vacuum over 

-

300mmHg look for an expiration date on the canister (where applicable) 

 

and change the canister if the canister has passed the expiration date to minimize the possibility of 

 

 

implosion, which can occur when a canister is aged or damaged.

 

 

6. External equipment intended for connection to signal input, signal output or other connectors, shall 

 

 

comply with relevant IEC standard (e.g. IEC 60950 for IT equipment and the IEC 60601 series for medical 

 

 

electrical equipment). In addition, all such combinations–systems –

 

shall comply with the standard IEC 

 

60601

-

1

-

1, safety requirements for medical electrical systems. Equipment not complying with IEC 60601 

 

shall be kept outside the patient environment, as defined in the standard. Any person who connects 

 

 

external equipment to signal input, signal output or other connectors has formed a system and is there

 

fore responsible for the system to comply with the requirements of IEC 60601

-

1

-

1. If in doubt, contact 

 

qualified technician or your local representative.

 

 

7. A blinking LED on the control panel indicates low battery capacity. This means the battery has been 

 

 

subjected to irreparable damage. REPLACE THE BATTERY! Replacement battery may be purchased at 

 

shop.sscor.com.

 

 

8. Where the integrity of the external protective earth conductor arrangement (ground) is in doubt, the unit 

 

shall be operated from its internal electrical power source (battery only). Grounding reliability can only be 

 

achieved when connected to an equivalent receptacle marked 

Hospital Only

” 

or 

Hospital Grade

” 

 

 

 

SSCOR Duet®

 

Model 2314 Series 

-

 AC suction unit with battery back

-

up

 

©2015 Duet, HI

-

D and Big Stick are registered trademarks of SSCOR, Inc.

 

SSCOR DUET 

-

 Model 2314 Series

 

Rev Y (11/18) 

 

2

 

Clearing The Airway Is Our #1 Priority

 

Caution

-

Notice

 

Revision Y (11/18)

 

Summary of Contents for DUET 2314 Series













Reviews: