English Manual
Page 8
1019548-A
Assembly
2.
Hitch Assembly Steps
and Mounting to UTV Steps
Insert the hitch tube (
1
) into the UTV receiver
and lock in place using the hitch pin (
5
) and the
cotter pin (
14
).
3. Add a 3/8"
hex nut (
6
) to
the 3/8" x 2-1/4
carriage bolt (
9
).
Slide this
bolt through
the adjustment
plate (
2
) using
the remaining
3/8" nut (
6
).
NOTE:
Move the carriage
bolt (
9
) up as far
as possible so it
will be out of
the way.
4. Slide the hitch tube (
1
) into the adjustment plate
(
2
) at the base, as illustrated here.
Add a 3/8" washer (
13
) to two 3/8 hex bolts (
11
).
Run these bolts through the adjustment plate (
2
)
and the hitch tube (
1
). Secure with another 3/8"
washer (
13
) and 3/8" nylon lock nut (
7
). Tighten the
bolts down.
5. Insert the six plastic square plugs (
4
) into the
openings of the spreader mount (
3
).
1.
Identifying Hardware
For reassurance, lay the nuts, bolts and washers
down on page 5 to verify you’re using the correct
parts during assembly.
Hardware Identifier
DO NOT RETU
RN PRODUCT I
F YOU ARE M
ISSING PARTS
.
PLEASE CALL
: 1 (800) 972-61
30
ILLUSTRATION
S ON THIS P
AGE ARE TO S
CALE FOR FAS
TER
IDENTIFICATIO
N OF HARDWAR
E DURING ASS
EMBLY.
Bolt: Carriage
, 3/8 x 2-1/4” (
x1) . . . . . . . . . . . . . . . . . . . . . . . .
11M1236P
9
Bolt: Hex H
ead, 3/8 x 3
-1/2” (x4) . . . . . .
2M1256P
11
Bolt: Hex H
ead, 1/2” x 3
” (x4) . . . . . . . . . . . . .
2M1648P
10
Nut: Reg H
ex,
3/8” -16 (x2)
. . . . . . . . . . . . . .
30M1200P
6
Nut: Nylon L
ock,
3/8” -16 (x4)
. . . . . . . . . . . . . .
B-4820
7
Nut: Nylon L
ock
1/2” (x4) . . . . . . . . . . . . . . .
B-5096Y
8
ADDITIONAL HARD
WARE
( Only needed f
or the Lesco H
itch )
Hairpin Cotte
r (x1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
D-146P
14
* Exterior circu
mference of w
ashers ca
are a measurem
Washer:
Flat, 1/2” (x8)
45M1717
P
12
Washer: SAE
Flat, 3/8” (x8
)
45M1313
P
13
Hardware Identifier
DO NOT RETU
RN PRODUCT I
F YOU ARE M
ISSING PARTS
.
PLEASE CALL
: 1 (800) 972-61
30
ILLUSTRATION
S ON THIS P
AGE ARE TO S
CALE FOR FAS
TER
IDENTIFICATIO
N OF HARDWAR
E DURING ASS
EMBLY.
Bolt: Carriage
, 3/8 x 2-1/4” (
x1) . . . . . . . . . . . . . . . . . . . . . . . .
11M1236P
9
Bolt: Hex H
ead, 3/8 x 3
-1/2” (x4) . . . . . .
2M1256P
11
Bolt: Hex H
ead, 1/2” x 3
” (x4) . . . . . . . . . . . . .
2M1648P
10
Nut: Reg H
ex,
3/8” -16 (x2)
. . . . . . . . . . . . . .
30M1200P
6
Nut: Nylon L
ock,
3/8” -16 (x4)
. . . . . . . . . . . . . .
B-4820
7
Hairpin Cotte
r (x1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
D-146P
14
Washer:
Flat, 1/2” (x8)
45M1717
P
12
Fig. 1
6
6
9
2
Fig. 2
13
13
13
7
13
2
11
1
Side View
after Assembly
Fig. 3
3
4
4
4
4
4
4
4