background image

SPLITFIRE SPEEDFIRE UPPERCUT 

15 

Further, the warranty does not cover: 
Fault finding, direct or indirect travel costs, transport costs, travel costs, allowances, 
accommodation and such. 

SPT bears no responsibility whatsoever for consequential damages caused by fault 
in its products, such as, but not limited to, loss of revenue, damages to 3

rd

 party, 

production delays, penalties etc. 

The warranty is not valid if modifications of any kind has been made to the product, 
without the written approval from SPT. Repairs made by non-authorised service 
personnel renders the warranty void. 

A modified product will be restored to the original state at the expense of the 
customer prior to any repair, as SPT can not be responsible for the function of its 
products otherwise. 

Warranty on replaced parts 
A replaced part will be covered by the original warranty. If less than 6 months 
remains from the warranty period, a replaced part will be covered for maximum 
months. 

Disputes 
Disputes will be handled according to the general terms in Orgalime S 2000. 

9. RECYCLING

Do not throw electrical equipment in the regular rubbish! According 
to EU-directive 2002/96/EG regarding waste that contains electric or 
electronic parts (WEEE) and its implementation with national laws 
products must be collected separately and brought to approved 
recycling facilities after their useful life. As the owner of the product 
you should find out the location of an approved recycling facility from 
your local dealer. 

Summary of Contents for SPEEDFIRE
















Reviews: