SprayTECH 0507008 Owner'S Manual Download

Page: 24 / 25

Accessories

Part No.

Description

0297xxx

RC Tip Assembly

0502xxx

Replacement Core, RC Tip

0297078

Tip Guard, RC Tip (11/16”)

0297070

Tip Guard, RC Tip (7/8”)

0291004

Hose, Whip End, 3' x 3/16"

0291003

Hose, Whip End, 5’ x 3/16”

0291002

Hose, Wireless, 25’ x 1/4"

0291000

Hose, Wireless, 50’ x 1/4"

0093896

Hose Connector, 1/4” x 1/4”M

0088154

Pressure Gauge

0152001

Power Roller Gun Attachment

0152308

9" Roller Cover, 3/8” Nap

0152307

9" Roller Cover, 1/2” Nap

0152309

9" Roller Cover, 3/4” Nap

0152310

9" Roller Cover, 1-1/4” Nap

0152235

12" Roller Cover, 1/2" Nap

0152236

12" Roller Cover, 3/8" Nap

0152237

12" Roller Cover, 3/4" Nap

0152238

12" Roller Cover, 1-1/4" Nap

0152700

Adapter, Power Roller Extension

0270145

G-10 Four Finger Airless Spray Gun (no tip)

0093930

Anti-Seize Compound

0152909

R-10 Telescoping Roller, 9", 3/8" Nap

0152900

R-10 Telescoping 12" Roller, 3/8" Nap

0502007

G-10 Four Finger Airless Spray Gun with 517
Reversible Tip

0502011

G-10 Two Finger Airless Spray Gun (no tip)

0502009

G-10 Two Finger Airless Spray Gun with 517
Reversible TIp

0270214

G-10 Four Finger Spray Pack with 50’ x 1/4”
airless hose

0502012

G-10 Two Finger Spray Pack with 50” x 1/4”
Airless Hose

0279920

Separating oil

0507958

Electrostatic discharge (ESD) wrist strap

9870307

Grease, 6 lb. can

Electronic

Control Assy

BLACK/RED/WHITE

Transducer

0507737

BLACK

WHITE

BLACK

ORANGE

GREEN

Wire Assembly

0507962

Ground to

Gear Housing

Circuit

Breaker

0507753

Plug

Relay

0507754

Potentiometer Assy

0507759

Motor

Electrical Schematic

NOTE: All electrical work should be performed by

a SprayTECH authorized service center.

PRIME/SPRAY Valve Assembly
(P/N 0507690)

Item

Part #

Description

Quantity

0507736

Dowel pin ....................................................1

0507745

Gasket ........................................................1

5000529

O-ring,

PTFE

..............................................1

0507741

O-ring, Viton................................................1

0507744

Valve housing .............................................1

0507746

Valve seat ...................................................1

0507743

Valve stem ..................................................1

5006547

O-ring, Viton................................................1

0507747

Spring .........................................................1

0507742

Valve retainer..............................................1

0507735

Cam base ...................................................1

5006543

Groove pin ..................................................1

0507662

Valve handle ...............................................1

Summary of Contents for 0507008


























Search results

Summary of Contents for 0507008

Reviews:

Related manuals for 0507008

Brands by name

Popular brands

SprayTECH 0507008, Owner'S Manual

Search results

Summary of Contents for 0507008

Reviews:

Related manuals for 0507008

Brands by name

Popular brands