background image

Evolution 12-25 D

SWITCHING ON THE LAMP

For models designed for switching the lamp on by 
DMX control (Evo 25), this is done selecting the 
corrisponding channel (see following instructions  in 
chapter “DMX Adjustment”) and refer to the switch 
on diagram (MANUAL and AUTO mode) shown on the 
following pages.
For models without switch on of lamp by DMX (Evo 12) 
press the appropriate button for approx. 2 seconds to 
switch on the lamp.
In luminaires using cold restrike lamps, wait a few 
minutes between each switching on.
Do not insist in switching on a hot lamp since this will 
unnecessarily reduce lamp life.
On switching on its first, the luminaire  may produce a 
little smoke. This should be considered as normal at first 
exposure  to heath of the parts closer to the lamp.

SWITCHING OFF THE LAMP

For the models with DMX control, set the value of the 
control channel of the lamp within the appropriate 
range (see following instructions and table in chapter 
“DMX Adjustment”).
For other models (Evo 12), switch on the mains on the 
ballast.

ELECTRICAL CONNECTIONS

Your luminaire has been designed for a supply voltage 
of 220-240V, 50Hz
The power cable complies with standards CEI 20-35. 

Before and during the installation, follow the 
instructions below:

• Always check the earth wiring for the line being used
• Ensure the voltage for the unit is the same as the one 

used for the supply (220-240V, 50Hz)

• Verify the luminaire is connected to the ballast 

• The product is designed for indoor use: consequently 

it has to be protected from dampness and rain, if used 
in different conditions

• Do not use lamps wich are different from the ones 

listed in the lamp table

• The luminaire can not be connected to dimmer. 

It is fitted with an internal mechanical dimmer, DMX 
controlled.

• Connect the DMX cable to the appropriate 5 pole XLR 

connector marked “DMX IN”

• Power the luminaire with the switch on the ballast
• Select the channel for dimmer adjustment on the 

display of dmx control 

• For models fitted with switching on and off of the 

lamp by DMX control, select the appropriate dimmer 
channel for this function (see following instruction in 
chapter “DMX Adjustment”)

WARNING: The luminaire must always be 
grounded

WARNING: When switched on, lamp produces 
high tension for a few seconds.

10

Summary of Contents for Evolution EVO 12 DC ZW

















Reviews: