background image

Page 8 

Hardware Required

#17. Bolt (M6x12 mm)

        [4 Pieces]

#22. Washer (M6)

        [2 Pieces]

#26. Spring Washer (M6)

        [4 Pieces]

#28. Arc Washer (M6)

        [2 Pieces]

Bolt

Washer

After complete assembly: If the computer is

not picking up your hand pulse signal 

(or you 

are getting inaccurate readings), Please refer 

to our “Troubleshooting” section on 

Page 1

1

 

for

other troubleshoot issues.

HAND PULSE SIGNAL

Troubleshooting

A s s e m b l y   S t e p   4

A.) Attach 

Handlebar (#04)

 to the 

Main Frame (#02)

, AND secure them together by using two 

Bolts (#17)

,

two

Spring Washers (#26) 

and two 

Washers (#22)

 from the sides, and two 

Bolts (#17)

, two

 Spring 

Washers (#26)

 and two 

Arc Washers (#28)

 from the front.

B.) Connect the 

Monitor Wire (Upper) (#45) 

to the

 Monitor Wire (Lower) (#46)

 as shown in the 

illustration below. 

The assembly process is now complete. 

However 

, for your own safety, please make sure to read this 

entire Owner’s Manual which includes safety instructions and warnings, as well as any safety/warning labels

affixed to the product before use. 

For your safety, please visually and functionally inspect and test the unit after assembly is complete. 

Assembly Instructions

  XRB

358 

Summary of Contents for BODYFIT XRB358

















Reviews: